Hi Guys and i m soo sorry for this post here!I Heard a threats that y could emulate cisco MARS on vmware for stuying purpose?is it poosible?if so pls list the methode for thatThanks
Hi Guys and i m soo sorry for this post here!I Heard a threats that y could emulate cisco MARS on vmware for stuying purpose?is it poosible?if so pls list the methode for thatThanks
initially i had a mgt router with an ip address of 192.168.119.250. I was unable to telnet to it from my desktop which sits on another subnetI was however able to telnet to it from the gw. When i logged into the router i noticed the default gateway w...
Aplogies if this is not a WAN topic...What is the difference between a PA-T3 and PA-T3+. I have looked at the module guides but can seem to come across a real difference. I basically want to know if I can replace a PA-T3+ with a PA-T3.If there is a b...
Need some help figuring out what my problem is here with NAT not being performed on our data connections using Ability File Server 1.20 (Code-crafters.com) along with the Linksys/Cisco RV042 router.The server sees and accepts client connections on po...
Can someone please tell me what exactly this command does?ip dhcp use vrf connectedORno ip dhcp use vrf connected
When is there a performance hit when you subinterface a gigabit ethernet port?We have a remote site with approxy 100-150 nodes. There is no layer 3 switch currently with which to implement VLANs. How bad of an idea is it to subinterface the router's ...
Dear Experts,I m new for BGP Routing. I have shown topology and IGP Routing using OSPF.How can I configure BGP routing on Router 3845 - 1 (CE) and Router 3845 - 2.(CE)Router 3845 - 1 AS no is : 65372Router 3845 - 2 AS no is 65375How can I configure B...
I am trying to redistribute a single IP from OSPF into BGP...You can see the ACL where I want to redistribute the single IP and not the entire subnet...but I don't see it in the BGP routing table...Any ideas?router ospf 100 log-adjacency-changes area...
does Onboard LAN Ports of 2821 isr support l3 routing? can them config as switchport access vlan?
frnzz, I have a scenario which I need to implement on my remote office network plzz help on this. I have a remote office connected to main office through L3 MPLS 2Mbps.(Due to the recent recession bandwidth up gradation is not approved users from thi...
HiI have two VRFs on the same multi-vrf CE router.If I export the routes of a VRF into the other VRF I have seen in the VRF routing table that the routes exported have an administrative distance of 20.It seems that they are seen like E-BGP routes.Why...
Hello,I'm trying to move a Linksys router out of my network.The Linksys router is currently configured with a DMZ zone that forwards all traffic to a specific IP, say 192.168.1.10.The Linksys router is also configured to PAT port 21 to another IP, sa...
Hello Folks,I am using a Catalyst 3560 and I want to block TCP and UDP ports on it. I've read that it is only possible to block incoming traffic on ports. Is that true? I am not sure, how to do this exactly. At the manual for the switch, there are tw...
ip host hostname port IPcan i get the clarification of this , if any document relating
Hi,My router is 2851 and running :c2800nm-adventerprisek9-mz.124-24.T2.binAnd I have 13 differenet IPSec vpn tunnels to other locationsHow can I find the each VPN tunnel bandwidthI explore teh NBAR method, aand its dont recognise IPSEC trafficAnd,sh ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |