Hi Folks Wonder if you could help have an ISR 4331 with an SFP (SFP-GB-GE-T) in interface G0/0/2. It is set for auto negotiation and negotiates to 100M/Full duplex to an ADVA NTE. Although the interface comes up I am seeing CRC errors. The circuit th...
) Now in the snippet below step 5 mentions "Install the best-path route into the global RIB, process outbound rules... then advertise to BGP peers" My question is this statement referring to the best route being advertised from the global-RIB or the ...
how to connect this router (the one at the top) to the 3 switches at the bottom, these are 2 different networks with 2 different subnet masks. I did the interface encapsulation but it doesn't send packets from any pc in Sales & Marketing Network (the...
Hello, l need to advertise by BGP two host IP addresses for example 1.1.1.33/24 and 1.1.1.34/24, they belong one subnet /24, terminating on subinterface. I need to advertise 1.1.1.33/24 to one bgp peer, 1.1.1.34/24 to another bgp peer, but in routing...
I am working on getting my router and switch to work with my cable modem. I have gotten the router to see the outside world and ping addresses. I am now working on the switch and having issues. I have my router connected to port 24 on my 2950 ci...
I have openvpn client on Windows 11 which started to sometimes work and sometimes not (after years of working ok). Two changes I made were windows upgrade and getting a Dell docking station with UTP jack (before was always wireless). I found out if I...
Im new to Vlans and static routing. I got assignment that have scenario like this :There's two building 1 is "Teknologi Maklumat" and 2 is "Matematik" and each building have 3 vlan. I know how to make vlan for each subgroups. But i dont know how to m...
Can't enable boost license config)#platform hardware throughput level boost not available. FLM240302GF_20220520020540.lic was installed and Version 16.8.3 Fuji I thought was the requirement, what am I missing. Index 11 Feature: booster_performanc...
Hello, Seeking help to as why my ping in a different WAN/router alternates rto/reply compared to my other WAN/router. I have no routing protocol configured to both links. I'll be more happy for a discussion. Thank you!
We will be migrating to SDWAN and OSPF routing between our global offices. We have about 40 sites (1 or 2 hub sites, the rest spoke sites) and hope to keep it all in one area 0. Should we be worried about the OSPF database becoming too large and poss...
Hi All, How can i monitor my STP events (TCN, new root election) through SNMP?SNMP MIBs and Traps on the ASA - Additional Information
Hi All, We have 1x 4331 router that is connecting to 2 different ISPs, from ISP A we have BGP setup with them and ISP B they're just giving us a static route. As of now, on the 4331 there is a default route to 0.0.0.0 via the static route for ISP B a...
1. How to configure BGP incoming traffic & outgoing Traffic?2. How to configure BGP primary if it goes down and switch over to secondary automatically?3. What is a router reflector? Why use a Router reflector? What is the purpose?4. What is BGP split...
Hi We are a company of about 40 people right now and we are thinking of changing our ISP router (wich is like a home device) from a cisco router. They gave us the following choices from the cheapest to the more expensive: Router Cisco 4331Router Cisc...
Greetings, When you go to the new customer and you have to support/Troubleshoot the network (in this case is OSPF) how will you proceed or what commands will you use in the network to know how ospf is working? thanks.
