Hai,sorry to ask this basic quistion can some one tell what does this xcatly mean by Loop back Not Set .. ..(out put of show interface)thx in advnceLijesh.N.C
Hai,sorry to ask this basic quistion can some one tell what does this xcatly mean by Loop back Not Set .. ..(out put of show interface)thx in advnceLijesh.N.C
Hi, Currently i have ISP setup which is running in active/pasive mode means.I have four router 1).Two Router in Core -OSPF & IBGP2).Two router in Distribution--OSPF & IBGPCore RoutCore Router-1 is having LP-300 so incoming will be prefereed from Co...
I need to monitor and see in the logs the error and status messages of the PSUs in a 3745 with IOS 12.4(10) Advianced IP Services images.I get those notifications on the console but not on the logs.Thank you in advance for your help.
Dear All,Everyone please help me i would like to know Cisco router 1841 can support VPN client( 60 clients or not?)Best Regards,Nroung
After a recent Chassis change on our dear 7507 router (using RSP-16), we observed that following command started failing for slavecs7:ITP#cs7 save route-table disk0:/route_20080905.txtRoute-table 'system' saved to 'disk0:/route_20080905.txt'Copying '...
A quick question:- From our gateway, when I run sh ip cef exact-route [customer ip] [some ip], I get a different next hop than the one listed when a traceroute is done from the actual ip ....Does that mean there are inconsistencies in the cef FIB ?Ho...
I have 2 routers setup for BGP and want .177 to be the preferred route. How can I accomplish this? No matter what I tried .178 always wants to be the preferred route. I have tried changing the local-preference but that doesn't help.Attached are the 2...
with out contacting the ISP is there any way to know the actual BW on a LINK if I do a SH INT SERIAL it may show me the BW that may not be the true BW ?
Hi,Can someone advice if the following will work?access-list 101 permit tcp 100.100.100.2 255.255.255.254 200.200.200.2 255.255.255.254 eq 888class-map match-all test match access-group 101class-map match-any voice-test match ip dscp efpolicy-map tes...
I have a static IP from AT&T for an ADSL connection. My router is an 1841 with an ATM (with ADSL module). I have a username and password and the IP/mask/gw from AT&T but I'm not sure if I have my config correct. All the interfaces that I think are in...
I have NEW AT&T PNT MPLS Network with 10 remote sites. The entire network will be running BGP. All remote CE locations will have different ASN's.I have 2 of my locations that have internet connections. CE1 and CE2I want to be able to send half of my ...
I have 3845 Series routers.We are getting CPU Utilization high frequently.At the time of CPU HIgh.It will give below msges 267 143384208 1064955 134646 94.43% 93.14% 94.52% 0 SNMP ENGINEThis is the IOS.ROM: System Bootstrap, Version 12.3(1...
I have been scratching my head for quite a while on this one ...We are a wisp, getting our internet connection from 6 DSL lines through 2 cisco boxes (3 lines on each). The cisco boxes feed a linux machine with 3 Nics that redistribute the traffic i...
My problem is two fold; the first is that on my primary & secondary (internet) routers I'm running HSRP t. We track the FE interface but on the primary router the FE is connected to a passive switch and then our vendor takes the link to Sprint. Whe...
Hi, I currently have a 2611XM and a 1720 router setup with a GRE tunnel between them running over Ipsec. When I run 'show processes cpu', the 'Encrypt Proc' process is always consuming a high percentage of the cpu resources. This affects the throughp...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-13-2024 06:16 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM |
User | Count |
---|---|
13 | |
10 | |
9 | |
6 | |
4 |