Hi,I have upgraded my Cisco Nexus C93180YC-FX yesterday from NXOS 10.2(6)M to NXOS 10.3(4a)M, but I seem that I have an error when I make "sh logging last 10".2024 Apr 30 09:39:09 edge01.par03 %DAEMON-3-SYSTEM_MSG: error: Unable to open the btmp file...
Forum Posts
HelloBeen a while since I've done this and am hoping to get a sanity check before I get too deep. I'm inheriting a lot of strangeness and am trying to sort things out as I go; please excuse the mess. This is the situation:Site A has two Catalyst 9500...
Resolved! The purpose of BGP cost community
Hi,I'm confused as to the reason for the existence of the BGP Cost community.Surely what it does can be achieved by using path attributes. E.g. weight, if you only want to influence a single router, or local preference if you want to affect the entir...
I am trying to go from a layer 3 port and use three different bridges with vrf going to one vlan in a router going to another router with same configuration. I unsure of how to do this because all the documentation is for switches or is too old to be...
Getting slow speed while sending traffic gre tunnel with ipsec
Our main office is connected to satellite office via a layer 2 1gbps EPL, and both offices are on the same subnet. The main office's gateway is 172.16.4.1 which is the on-prem firewall connected to a 1gbps DIA circuit. The satellite office's gateway ...
BGP does not have a neighbor with the peer. It is not in the routing table.I think it may be something with the image.RP/0/0/CPU0:ISP#sh runnFri May 2 13:04:06.978 UTCBuilding configuration...!! IOS XR ConfigurationRP/0/0/CPU0:SP#sh routeFri May 2 13...
I have a 2911 that I am setting up as a Terminal server to connect to other Cisco devices out of band. I have the line interface plugged into WIC slot 3 which give me lines 35-50. I have configured the line as 2035-2042 since I only have 1 octal ca...
Hello, I am facing issues regarding connectivity as I am fairly new to BGP and route redistribution.In my topology there are 3 autonomous systems with eBGP running between them, each AS is running iBGP and a different IGP. I am trying to redistribute...
HelloPlease refer below diagramWe are using the default-information originate on cedgesbut when DIA 1 is unreachable or i apply an acl with deny all on the isp interface still it advertises the default route in ospfIs there a way to use an ip sla and...
Hi All, I was doing a multicast lab to understand more about multicast routing. I have sparse-dense-mode running on all the interfaces. This is the routing table from one of the devices. Unlike the unicast routing table, this mroute table is bit more...
hi,we have a 4K SIP router and got some issue with outbound calls.saw these logs and PVDM4 stucked in 'booting'the PVDM4 still shows in the 'show inventory'my questions are:1.can this be resolved by a reboot?2.or do i need to reseat the PVDM4 module?...
is cisco have upgrade path of ios xe from 16.9.4 to 17.9.5f on isr 4321? i can directly upgrade it from 16.9.4 to 17.9.5?
Hello guys,I need some help about routing between my core router and segmentation firewall.My topology: Asr920>iBGP>fortigate seg.fw>iBGP>perimter cisco frp with fmcPortchannel as trunk with service ethernet instacne to fw, allowed BDI.Comunication i...
Hello Guys,We are planning to upgrade Cisco router Cisco C8300-1N1S-4T2X from XE image 17.6.5 (Rommon image 17.3(5r)) to latest XE image 17.9.5a. As per Rommon compatibility matrix, this new XE image should have minimum rommon image of 17.3(1r) and m...
