Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

I am building a home lab. I have 4 2620 routers and 4 3550 switches. My question is can I use one of this routers to access the other routers and switches rather that moving the console cable every time I access the other devices? Also can one of...

Has any one got any extra information regarding ip sla monitor. Im having prblms understanding how to apply access list and route map. I have read the pdf on Reliable Static Routing Backup UsingObject Tracking. Which is my scenario. But something is ...

cm by Level 1
  • 462 Views
  • 1 replies
  • 0 Helpful votes

I have a network, OSPF is the protocol, now i want to add one more network in it, but both the networks should be separte from each other, there is no more availabe physical iterfaces are on my devices. Can i meet my requirement..??

I using 2 seperate router for 2 external connection and this is connected to one router which is connected to my LAN using firewall. The external link is MPLS and i am using OSPF.The first external connecting is configured as area 0 and second is ar...

drnteam by Level 1
  • 919 Views
  • 6 replies
  • 0 Helpful votes

Hi All, I need understanding the lines below. For some reason the "ge" option in the prefix list is throwing me off. So far, I understand it as BGP will NOT advertise X.X.160.0 out. Is that correct?PREFIX LISTip prefix-list OUT seq 5 permit X.X.160.0...

merryllem by Level 1
  • 8618 Views
  • 4 replies
  • 0 Helpful votes

We have a customer that for all intents and purposes have 2 100Mbps Internet connections. They serve several customers with their own networks. My plan was to manipulate which links this traffic uses via Weight and AS Path Prepends with route maps ...

Hello. I'm a newbie so I use graphical interface to configure my cisco router 871I have 2 networksn1: 10.0.0.0 /24n2: 192.168.1.0 /24 192.168.1.252 is the gateway to internetn1 has not access to the internetn2 has the access to the internet using ...

hi Switching Gurus,My setup is as follows,access switch --> distrribution switch--> core switch --> router.I want to achieve end-end QoS for VoIP and on the Access switch we are doing "trust DSCP".On the trunk interfaces am I supposed to do "trust Co...

saimbt by Level 1
  • 756 Views
  • 5 replies
  • 0 Helpful votes

Hi,I have setup a network to test the routing and observe below result that I don't understand. Can anyone help to explain it. Thanks!-16A RouterAll E2 route [110/1] learned --I don't know why the metric is 1 as I redistribute bgp route into ospf wit...

acbenny by Level 1
  • 905 Views
  • 5 replies
  • 0 Helpful votes

We are putting in a point-to-point, bonded T1. We have a cisco 2821 router in our local site. The router has 2 ports labeled GE0/1 and GE0/2 and two T1 ports (WIC). Will this handle the bonded T1 lines? Also, what would we need to put in our remo...

d.elias by Level 1
  • 524 Views
  • 1 replies
  • 0 Helpful votes

As an ISP I have 5 BGP sessions, one of my main AS paths is having major issues on a reg basis so I want to change the load to be "stronger" on another path. Is this just a matter of going from below ....route-map ATT_Test permit 5 match as-path 17 ...

cozyk1515 by Level 1
  • 1841 Views
  • 10 replies
  • 0 Helpful votes