Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Dear all I have cisco 2800 router and a juniper j2300 router. I have to make it a serial comunication over the cisco to juniper I have two question1) The cisco cables are compatible with juniper or not ? 2)how to done the handshakinig between the cis...

Resolved! PBR 2821 2ISP

Hi I have 2821 and 2 ISP. I want for network's 10.10.60.0 - 10.10.61.0 goto over ISP 1, and all remained over isp2. It's work! But in this configuration not work routing between network. For example: 10.10.60.0 not route 10.10.10.0, 10.10.10.0 not r...

Hi folks,if I have 2 switches with only one link between them and no redundancy then add a new switch which has a lower BID than the other 2 switches over a single link do all my ports on all my switches transition into the listening then learning st...

d.hodgson by Level 1
  • 447 Views
  • 1 replies
  • 0 Helpful votes

We are having this issue with our t1 where the router will go down and show an AIS error. THe last time a reboot fixed the issue. I think it maybe a bad WIC. I have matched the line settings on both ends, checked clock source, checked all cables, ...

gusy i m pretty new to this....i have a question infact series of questions which relates to IpSEC....my understanding is that IPSEC (plz correct me if i am wrong) is an open standard......IKE is a negotion protocol of IPSEC......IPSEC has three main...

Experts,Can any one let me know how to configure CISCO Load Balancing to my SAP Landscape.We have implemented SAP Enterprise Portal,We want to buy CISCO Product for Load Balancing,Can any one suggest me?

Is it possible to get an external ip-address on the wan interface of the asa, and let the router do the pppoa athentication. Even when the ISP has given you only one external ip-adres...? If yes how should the config looklike.Thnx

belewout by Level 1
  • 333 Views
  • 1 replies
  • 0 Helpful votes

Dear all,My company WAN connected is using Metro Ethernet 3M for each subinterface.I want to clarify four points, 1. Fa1/1 using speed 100. is it correct?2. Fa1/1.2701 & Fa1/1.2717 using "bandwidth 3072". is it correct?3. Fa1/1.2701 & Fa1/1.2717 usin...

Hi FriendI want to connect two ospf back bone are and make it single area, Like two office running ospf and now i want to connect that OSPF area 0 of both office, both are running private IP address .Please let me know-Minu

Dear experts,1. Do the above mentioned Routers series of 1841,2821 and 3825.Supportsdataalong with voice ?.2. If so then which type , whether FXO or FXS or both?3. If they do support voice and in FXO mode then up to how many lines ?4. Is Exchange nec...

HiI have Sun proxy server which is connect my router for internet. My user internet access via proxy. recently I found in MRTG is always high. so How I can findout which users are always download ?.ThanksBiplob

iqbalkhan by Level 1
  • 1684 Views
  • 7 replies
  • 0 Helpful votes

Hi FriendHow to get MPLS VPN Redundancy between two provider like One CE will have connectivity like CE-PE1 ( provider 1) and same CE- PE2 ( Provider 2) , How to get redundancy and failover. Please send me good documents also.-M

Resolved! reg:3640 config

Dear sir,iam having 3640 router in that alredy point to multipoint leased lines r working fine now in that router we have Nm-8am module how can i configure that module as a backup lines.pc-dialupmodem----dialup line ----3640 withnm8am---lan--serverno...