Hi,I have configured a VPN tunnel between Fortinet device and a Cisco 881 device.The phase1 and phase 2 came up and tunnel is up.It was a requirement by Fortinet to make the configuration in Aggressive Mode.The Cisco 881 will be configured on the of...
I made this network below in packet tracer. This is my packet tracer file.Even after going over this issue 13 times I'm not able to fix it . The problem is that I'm not able to see "OSPF Learned Routes" in the routing table of each of the four Area B...
Hi there,I just have a general question about OSPF . Does OSPF Algorithm selects the best path on basis of cost of interface or the link between two routers in same prefix and if that is true , what happens lets say if there are two routers in WAN an...
This ISR 4431 is running 16.9.3. When i use the following to install 16.12.4 it appears to install correctly:install add file ftp://username:password@10.10.5.13/isr4400-universalk9.16.12.04.SPA.bin activate commitIt prompts me to set the boot variab...
Is EIGRP a Layer3 or Layer4 ? Does it sit on top of IP Layer?
HelloHope you guys are well! I need some help regarding interface statistics. Below are the interface statistics. Core-Router#show interfaces gigabitEthernet 0/0GigabitEthernet0/0 is up, line protocol is upHardware is BCM1125 Internal MAC, address is...
Hi, i am trying to configure telnet access to management interface on ASR router, but strangely telnet logs me only in diagmode.Anyone ever experienced this kind of problem?Here is the config for VTY lines. line VTY 0 4session-timeout 30access-class ...
Hello all, I have 2911 with PVDM 3-16, 4FXO, and CUCM 11.5 which has 4 analog lines and 50 DNs I want to implement IVR in my office but its really confusing. I have gone through internet and there are:Unity ConnectionUCCXand some hardwares like Cisco...
sorry for my bad english. when connecting PPP I have this error : May 27 06:51:35.599: PPPoE handle inconsistency: handle 0x580003AF returns session 0x7FEB6F0BE280 with handle 0x0May 27 06:51:35.599: SSS PM: SSS PM: Added peruser feature infos when c...
Hello Everybody. I would ask you regard this way to advertise a default route into EIGRP.I've read it on some blog: "Option #2The second method for injecting a default route into EIGRP is to configure a network command with 0.0.0.0. You must have the...
If I pair up two routers using eBGP using loopbacks as the source and one router between them, the ebgp-multihop 2 command lets them come up as neighbors. This should not work however as they are more than 2 hops away. For example I have the followin...
Hi,I try to add a delayed reload at the end of an event manager script that can ba canceled by another script if a defined "good" event happens. event manager applet CONFIGURE... action 98 cli command "reload in 10"!event manager applet STOP_RELOAD e...
Hi,Could anyone know how to enable the 'crypto ikev2' on ISRs? The only alternatives are:R1(config)#crypto ?RSA-key-pair RSA key pairkey Long term key operationspki Public Key componentsprovisioning Secure Device Provisioningwui Crypto HTTP configura...
Hi I was wondering if ASR1001-X has L2 switching Module that Support VRRP
Hi everyone, I finally have managed to set up my Cisco C1111X-8P router for production use (thanks to everyone involved!). However, when I perform a speed test (www.speedtest.net) on my 1Gbit/s line, I can only manage to get around 500-600 Mbit/s. Th...
