The performance spec for the C11111-8p lists the router at 350meg . Is that the maximum over VPN, applications, or simple routed NAT. Our environment is primarily residential, with some small business - VPN performance isn't super critical, as it is...
Forum Posts
Resolved! ACLs in C9500
Hi all, we'd like to implement ACLs in our C9500 core switches. Could you please help with two (presumably quite easy) questions: Am I right that in extended ACLs on this switch there is no implicit deny at the end of every ACL? That's at least what ...
Resolved! Configuration BGP in Cisco Switch
I am looking for an order at the Configuration level BGP in switch Cisco which allows you to check if theneighbor is UP or down.to ensure link redundancy between two link configure with bgp, i need command to check link is up or down
Hi, I am trying to achieve multicast over our MPLS network. We use a GRE tunnels between our sites to establish an internal MPLS core. Using BGP we are able to route our enterprise VRFs between the sites. One of our VRFs requires bi-directional multi...
Going from a Netgear router that has a GUI that is built in and that I understand and moving to a Cisco router, c897va-k9, that has nothing but CLI that I am almost entirely unfamiliar with. Have gotten some help from the Cisco community but keep run...
Resolved! Cisco 5915 Serial Port Echo Problem
Hi everybody,I'm working on a project that connects to Cisco 5915 over serial port from an application. I guess, router is echoing that everything I send. For example, router> // router sendenable\r // I sendrouter>enable // router send and waiting f...
Hi we have switch/stacked switch 9300. The version is 17.3.3. In the below screenshot, there are many choices. I would like to know which one is best one for our switches and which one we can use? Thank you
Resolved! OSPF NSSA translator
Hello all, I just have a question I'm not able to find in the RFC We have an OSPF NSSA area with routers r2 and r3 acting as ABR. Then we have routers r4 and r5 internal in this area, so the topology would be r2 - r4- r5 -r3, with r2 and r3 both conn...
Resolved! OSPF multi area adjacency
Hello, I am trying to understand multi-area adjacency. r1----area0----r2|. || |area0. area0| || |r3-----area1--r4 R3's loopback:- 3.3..3.3 in...
Hello Everyone, r1--area1--r2----area0---r3--area2---r4--area0--r5---area1--r6 r1's loopback 1.1.1.1 in area 1r3's loopback 33.33.33.33 in area 2r4's loopback 44.44.44.44 in area 21) r3 has r1's loopback(1.1.1.1) in the routing table but it won't fo...
Hello Team,We want that all of our traffic from some vlan will go out from a specific IP For that, we have a route-map that the next hop is : 10.10.10.1It used to work in our CAT 6500, and all the traffic from vlan 10 got out well. Now, on our CAT 96...
Hi, Just wanted to know what hardware and license do i need to be able to support DMNR on a cisco1100 router Thanks
Hello Fellow Cisco Guru'sI would greatly appreciate your input and expertise regarding this issue.We have a web proxy in the form of a Web Securtiy Appliance *M390 - Management, & *S390s - Acting asPrimary & Secondary Gateways, Our LAN is going throu...
Resolved! Cisco 1900 Series
I have a cisco 1900 series router and I was not able to login using web interface. I used the administrator password which I normally use when using telnet or sshWhen I enter the user name and password it loads then goes back to the login pop up. Ple...
I successfully got a config to work on CenturyLink on a DSL circuit. But using that same config at a new location on a new (although same speed) circuit the EHWIC card doesn't seem to be working. I swapped the card with a known good one so that isn'...
