Hello Professionals, could somebody help me on this below error. As soon as I enter the network command in eigrp i am getting this error. below the is the entire configuration and topology attached. Please guide me what am I doing wrong here in routi...
Forum Posts
i Dear FriendsWe have several ASR 1002-x with IOS version: asr1002x-universalk9.16.06.07.SPAWe use these ASRs for PPPoE termination. Around 18K session per router.Each router has 16GB of RAM. Recently I noticed The memory usage of each router is incr...
Hello All,I am try to Connect my Cisco C1111-8PLTEEAWB to my Cisco 4321. I wan to use the C1111 Console-RJ45 or USB3 port to make a connection to the 4321 via its AUX port using reverse-telnet. Is this possible? I havent found a way. Creating this co...
I got an issue about Redistribution with Route-Map with ACL, but this ACL doesn't is shown in the config or it was deleted.First, my question is that if I delete an ACL associated with a redistribute route-map the match condition wouldn't happen so t...
MFWS-2911-R2#enablePassword:MFWS-2911-R2#sh confUsing 3347 out of 262136 bytes!! Last configuration change at 17:04:14 UTC Mon Jul 20 2020 by tom!version 15.7service timestamps debug datetime msecservice timestamps log datetime msecservice password-e...
Does virtual OS also use the public IP of outgoing router interface? So does this mean the destination network will detect my public IP of the router? How can I make virtual OS have a different public IP?
when I restart the cisco isr 1100, the vpn configuration is lost, I have to apply the copy startup config running config command to show all my router settings
I've been doing a lot of searching on this and can't seem to find any helpful information. I've read the CLI configuration guides and they don't really tell me what I need to know. My situation: I have a Nexus 9500 that is a BSR and C-RP. It is th...
Resolved! Routing Guide
Hi!I need to route all traffic destined for https://mywebrtcvoipserver.com to one hop. And all other traffic to another hop? How I can do that?
Hello, Let say I have one public AS number (AS1234 in this case) and have routers on 2 different datacenters. In both datacenters, there is a 6500 series (SUP2T) router, each one will announce 1-1 /24 prefixes. Datacenter A router announce 11.22.33.0...
Hi, I have crated a test lab, as below scenario: Two Routers' interfaces are connected to common switch, with 2 different Subnets, along with a 3rd Router. All Routes are in VLAN1.When enable EIGRP process on R1 for 10.0.1.0 & 10.0.2.0 got the messag...
Resolved! 1921 and 1602i Autonomous
Hello, I'm very new to cisco programming but I recently acquired a client that has a Cisco 1921 with a EHWIC-4ESG-P. One of the HWIC ports feeds a 1602i with POE. The client has an odd issue. That is, DHCP will not issue wired or wireless clients any...
import getpass import sys import telnetlib HOST = "192.168.1.1" user = raw_input("Enter your remote account: ") password = getpass.getpass() tn = telnetlib.Telnet(HOST) tn.read_until(b"Username: ") tn.write(user + "\n") if password: tn.read_un...
Hello everyone. I am a beginner in BGP configuration. I have a following bgp router file. I need to block network IP 1.0.0.0/8 to directly access that. All other IPs permitted to access. I tried to create an access list but it is not working probabl...
Hello all, I am labbing up some BGP stuff and am confused as to what is going on here. R1 and R2 are in AS 15, R3, R4 and R5 arein AS 10 and R6 is in AS 5.R1 and R2 have loop back interfaces in 100.100.100.0 and am advertising those using network sta...
