Hello, we have servers running multicast traffic on one site of our WAN however the core router at that site has multicast routing disabled. I have confirmed that on the CLI.However at another WAN site we can see multicast traffic coming that site in...
Forum Posts
Resolved! BGP best path selection
Hi,I am trying to get my head around best route selection but I couldn't get my head around it.BGP routing table entry for 99.94.160.21:100:99.99.99.0/24, version 193064 BGP Bestpath: deterministic-med Multipath: eBGP iBGP 763 4755 6453 2914 42 1928...
I have two ISP's, I want to utilize both circuits in an active/active scenario (not active/active as in a dual asa scenario). Would a route map for each ISP traffic be an answer for this? We have load balancers up front and they do round robin, I wou...
Hello, I am been working with a company in the past,during the tenure I completed CCIE Routing & Switching written 12th Jan 2016 and my certification account was registered with my company email ID. Now I am no more with the company and I would like ...
I have Cisco 1900 Series, with NAT and port forwarding configured.And port Forwarding works from internet, using the WAN IP and related port forwarding.And I also want to use the port forwarding from the LAN, by using the WAN IP.But from LAN, reachin...
Resolved! Advertise smaller BGP subnet
I have a router with 4 BGP neighbors, to which I am advertising a list of subnets. This list includesa handful of /14 and /15 ranges. However, I want to advertise a /29 within the /14 range withoutprepending the AS path. I have things like this:route...
Hi, I have one L2 switch having two vlan 4 & 5. I want communication between host of both vlans. How it can possible? Although I have configured Vlan-Bridge, but it is not workinginterface Vlan4 bridge-group 1!interface Vlan5 bridge-group 1!bridge 1 ...
In my L3# Switch I have a default route pointing to internet.ex: 0.0.0.0 0.0.0.0 next hop<x.x.x.x> So by default for any traffic not in the routing table, it will follow the default route.But would like to know , whether the static/default route can ...
I have two edge routers on my enterprise network that are both receiving a default route via BGP with my ISP. I want to be able to redistribute the default routes into my internal network, but preferring one over the other. I'm doing OSPF on these ro...
Hello everybody,I have the following topology. Network A needs to talk to Network B.I created Customer VRF on the middle PE (PE-X) and I successfully saw the routes from both sides, however Network A still cannot ping network B. also, traceroute show...
Dear all, I appreciate if you can let me know your feedback, in my opinion actually Cat3K can support limited layer 3 static routingon Stackwise with LAN base feature right? however if I have been investigating with CCO there is following information...
Resolved! Connect different networks with RIP
Hey, My project contains five different networks and my task is to connect them via RIP. Each network has a PC connected to it. My goal is to be able to ping every PC from each PC. I've already tried to add the different network addresses to Router ...
Hi Guys, If anyone can explain this, in brief, would be really appreciated. Question :Company A is running BGP to connect to external peers they were recently acquired and new peers(Company B) will be connecting using the acquiring company(Company A)...
Hi guys, This is one of the question I had on a paper. Can anyone explain the answer to this question briefly? Question: When configuring an aggregate address with BGP, What addition to the aggregate-address configuration is needed to only advertise ...
So, I know in the later released of IOS XE 16.8.x the default has been raised for IPSec throughput. But for people running IOS XE code before that, I would like some help in verifying IPSec Aggragate Throughput. From my understand, If I have a ISR 4k...
