Anyone here have experience using Automatic Transfer Switch power supplies for Cisco ISR 4000 routers?We want to use RPS for a/b AC power delivery but it’s not supported on the low-end models.The RPS states 60 μs switchover. We found an APC ATS but i...
Forum Posts
Hello,can anybody please give me a hint how many OSPF areas an ISR4331 router supports?Thank you in advance!
I am trying to get a sense of best practice approach here. Currently have two data centers that are connected to my branch offices via BGP into the ISP network. The plan is to send all default route traffic to one Data Center to get to the internet a...
I would like to make backups of my cisco devices using SCP from a linux filesystem. I am running the following command:scp username@192.168.1.1:flash/ /dir/to/backup...where 192.168.1.1 is the cisco device's IP. I get the following response to the ...
Hello all.i have recently had to change my network so now my RV325 is sat behind a Mitel Boarder Gateway in network edge mode. The WAN address is now on the MBG with the MBG LAN side 192.168.200.254 hitting the WAN port on the RV325 - 192.168.200.1Th...
Hello,I need to analyse in my syslog server (Splunk) the toppology on my router network (about 1000 routers).I suppose that activating the normal OSPF logs and sending then to the syslog server would not be enough because, in this case I would get on...
HelloI need some recommendation regarding choosing the right type of router. Mainly it will just handle a few GRE-tunnels at 1 Gbit or more and be able to failover with HSRP. Could the ASR-920 be a good choice or is the ISR series to be preferred? /T...
Hi,Can someone help me how to configure a IR829 for WAN failover to cellular 0 and vice-versa depending on network presence or failureThanksBas
Resolved! Complex NAT setup
Hi Guys, So I have a requirement where I need to setup a fairly complicated NAT config, and at the same time dealing with 2 or 3 other companies that are connecting different parts of the network and limiting my testing possibilities. It's going to ...
Hello all.i have recently had to change my network so now my RV325 is sat behind a Mitel Boarder Gateway in network edge mode. The wan address is now on the MBG with the MBG LAN side 192.168.200.254 hitting the WAN port on the RV325 - 192.168.200.1Th...
Resolved! unable to login. cisco 1941
Hi.I have a cisco 1941 router. First of all, a i can't connect via ssh (connection timed-out error). I tried to connect via console, but there is critical logging enabled, so i have no login request, only messages like these:-Traceback= 21032A70z 210...
Hi Guys, I want to disable failover for one of my context in cisco multi-context ASA which is configured with active/standby. I tried using the command 'failover' under the specific group as well as context but it is affecting for whole unit(all cont...
Resolved! Router-to-router communication failure
The router-to-router connection seems normal. However, if routers send PDU, Failed is displayed. I attached and image and my project.
Traffic flow for all the customers now:VLAN 476 --> R1 (g0/0/0) --> Switch(Port1) --> 4331 (g0/0/1) (NAT) -->Switch(Port22) --> R1 (g0/0/3) --> Internet. I need to separate Customer X Traffic from all other traffic and customer X traffic should be di...
Hi I have setup a lab with both eBGP and iBGP connections. I am noticing some strange results with iBGP.I am running iBGP between the loopbacks of two routers and do not have "next-hop self" set on the iBGP neighbours but still the routers are changi...
