12-01-2010 09:28 AM - edited 03-04-2019 10:38 AM
I have a cisco 2800 rtr, with 4 card slots. Rtr will not recognize or power t1 wic or t1vwic cards in any slot. IOS will not recognize serial / controller interfaces. HELP?
12-01-2010 09:56 AM
Hi ,
Sure, I can help you out with this. Please send "show version", "show inv", "show diag", "show run | inc card" from the 2800 Router with the T1 cards in the WIC slots.
Regards,
Om Prakash
12-01-2010 10:09 AM
here is the info, thanks for the help..as you can see, it see's the wic hardware on boot, but no interfaces...
sho ver:
Cisco IOS Software, 2801 Software (C2801-IPBASE-M), Version 12.4(1c), RELEASE SO
FTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 26-Oct-05 08:42 by evmiller
ROM: System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
BaptistManor uptime is 2 minutes
System returned to ROM by power-on
System image file is "flash:c2801-ipbase-mz.124-1c.bin"
Cisco 2801 (revision 6.0) with 114688K/16384K bytes of memory.
Processor board ID FTX1044W0VT
2 FastEthernet interfaces
2 Channelized (E1 or T1)/PRI ports
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
sho inv
AME: "2801 chassis", DESCR: "2801 chassis, Hw Serial#: 2651778995, Hw Revision:
6.0"
PID: CISCO2801 , VID: V03 , SN: FTX1044W0VT
NAME: "C2801 Motherboard with 2 Fast Ethernet", DESCR: "C2801 Motherboard with 2
Fast Ethernet"
PID: CISCO2801 , VID: 6.0, SN: FTX1044W0VT
NAME: "WIC/VIC 2", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/
E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: 4294967295
sho diag
C2801 2FE 4SLOT Mainboard Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Chassis MAC Address : 0019.aad2.ab4e
MAC Address block size : 34
PCB Serial Number : FOC10413SWH
Hardware Revision : 6.0
Part Number : 73-8190-06
Board Revision : B0
Top Assy. Part Number : 800-23435-04
Deviation Number : 0
Fab Version : 04
CLEI Code : IPM7S00CRA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : CISCO2801
Version Identifier : V03
Processor type : 86
Chassis Serial Number : FTX1044W0VT
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C3 06 00 19 AA D2 AB 4E 43 00 22 C1 8B 46
0x10: 4F 43 31 30 34 31 33 53 57 48 40 04 1C 41 06 00
0x20: 82 49 1F FE 06 42 42 30 C0 46 03 20 00 5B 8B 04
0x30: 88 00 00 00 00 02 04 C6 8A 49 50 4D 37 53 30 30
0x40: 43 52 41 03 00 81 00 00 00 00 04 00 CB 89 43 49
0x50: 53 43 4F 32 38 30 31 89 56 30 33 20 D9 02 C1 40
0x60: 09 86 C2 8B 46 54 58 31 30 34 34 57 30 56 54 FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x100: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x110: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x120: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x140: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
VIC Slot 0:
VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1
WIC module not supported/disabled in this slot
Hardware Revision : 0.0
Top Assy. Part Number : 800-22629-05
Board Revision : C0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC13453QP6
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VWIC2-2MFT-T1/E1
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 FC 41 00 00 C0 46 03 20 00 58 65 05
0x10: 42 43 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 33 34 35 33 51 50 36 03 00 81 00 00 00 00 04 00
0x30: CB 90 56 57 49 43 32 2D 32 4D 46 54 2D 54 31 2F
0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC/VIC Slot 2:
VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1
Hardware Revision : 0.0
Top Assy. Part Number : 800-22629-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC1042626J
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VWIC2-2MFT-T1/E1
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 FC 41 00 00 C0 46 03 20 00 58 65 05
0x10: 42 41 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 30 34 32 36 32 36 4A 03 00 81 00 00 00 00 04 00
0x30: CB 90 56 57 49 43 32 2D 32 4D 46 54 2D 54 31 2F
0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
sho run
BaptistManor#sho run
Building configuration...
Current configuration : 1482 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname BaptistManor
!
boot-start-marker
boot-end-marker
!
! card type command needed for slot 0
enable secret 5 $1$eyC.$XwGh76qfzTzRg4lQ9XwzZ/
!
no aaa new-model
!
resource policy
!
clock timezone CST -6
clock summer-time CDT recurring 2 Sun Mar 2:00 1 Sun Nov 2:00
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip domain name bhcpns.org
ip name-server 10.5.1.40
!
!
!
!
interface FastEthernet0/0
ip address 10.202.42.1 255.255.255.0
ip helper-address 10.5.1.40
ip helper-address 10.5.1.41
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
router ospf 1
log-adjacency-changes
area 10.202.0.0 stub no-summary
network 10.202.40.0 0.0.0.255 area 10.202.0.0
network 10.202.42.0 0.0.0.255 area 10.202.0.0
network 10.202.104.0 0.0.0.255 area 10.202.0.0
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.202.104.1
!
no ip http server
!
snmp-server community public RO
snmp-server community cap12 RW
snmp-server enable traps snmp authentication
snmp-server enable traps config
snmp-server host 10.5.1.50 public
!
control-plane
!
!
line con 0
password remote
login
line aux 0
password remote
login
line vty 0 4
password remote
login
!
ntp clock-period 17179667
ntp server 10.202.104.1
ntp server 10.7.1.10
end
12-01-2010 11:00 AM
Hello Billy,
when you no powered or not recognised means these interface are not showing when you type " sh ip int brief"
i did not the Card type command on your device can you add this
card type t1 0 0
card type t1 0 2
controller T1 0/0/0
framing esf
fdl both
linecode b8zs
channel-group 0 timeslots 1-24
!
controller T1 0/0/1
framing esf
linecode b8zs
channel-group 0 timeslots 1-24
!
controller T1 0/2/0
framing esf
fdl both
linecode b8zs
!
controller T1 0/2/1
framing esf
linecode b8zs
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide