Redistribution Static Route on NX-OS Nexus 7000

[malickmbaye]

Hello,

I have a N7K which is configured with multiple VDC (VDC-DIST and VDC-CORE). i have EIGRP routing activated on the two VDC and the neighboring is working fine. I am also able to redistributed direct network connected from the DIST to the CORE. But the redistribution of static routes created on DIST is not working. The CORE don't see those routes via the EIGRP. Can someone help me please, i am new on NX-OS

Configuration of DIST:

ip prefix-list REDISTRIBUTION seq 5 permit 0.0.0.0/0 le 32

route-map redist-static permit 10
match ip address prefix-list REDISTRIBUTION
redistribute direct route-map redist-static
redistribute static route-map redist-static

router eigrp VIN
autonomous-system 1
router-id 0.0.0.230
redistribute direct route-map redist-static
redistribute static route-map redist-static
address-family ipv4 unicast

ip route 10.254.0.152/30 10.101.222.100

------

The route 10.254.0.152 is not seen from the CORE.

[MHM Cisco World]

that all config, how eigrp form between two NSK SW ? 

MHM

[malickmbaye]

Hello,

Yes The eigrp is formed:

[MHM Cisco World]

show ip eigrp route-map statistics redistribute <<- can I see this 
MHM

[malickmbaye]

hello

[malickmbaye]

Hello,

[MHM Cisco World]

there is nothing wrong as I see 
there is EIGRP and route-map is match 2 prefix 
so you must see static route in other Peers 
except case you have route-map to filter which prefix learn from

can you confirm that there is no route-map or distribute list filter prefix Inbound ?

also try below 
instead 

Nexus-C(config)# router eigrp VIN
Nexus-C(config-router)# address-family ipv4 unicast
Nexus-C(config-router-af)# autonomous-system 1
Nexus-C(config-router-af)# router-id 0.0.0.255
Nexus-C(config-router-af)# redistribute static route-map  redist-static

sometime the nexus not run command until we add it under address family 
MHM

[MHM Cisco World]

I do lab yesterday ad as I mention you need to add redistribute static under address family 

[David Ruess]

Can you provide the routing table of DIST and CORE along with show ip eigrp topology on both devices.

Usually when you configure a static route and the next hop is unreachable it wont put it in the table, and therefore not redistribute it into EIGRP. If it is in fact redistributing it and passing it to its neighbor, you'll see it in the EIGRP topology table.

-David

[paul driver · Accepted solution]

Hello
try applying the redistribution under the AFI for ipv4 also maybe tag the static instead,   then test again

router eigrp vin
no redistribute direct route-map redist-static
no redistribute static route-map redist-static
address-family ipv4 unicast
redistribute static route-map redist-static

also possibly ...
ip route 10.254.0.152/30 10.101.222.100 tag 10

no route-map redist-static permit 10
route-map redist-static permit 10
match tag 10

[malickmbaye]

Hello,

The issue is solved with matching tag.

Thank you very much.

[MHM Cisco World]

Did you try with tag but add under address family ipv4 unicast? i.e. NOT need TAG 
FYI :-I already check it without tag and work 

MHM

[malickmbaye]

Will i lose the connection on the device when i apply it? Note that i am connected to an ip management which is known from eigrp

[MHM Cisco World]

OK that need to check (lost of connection)

ip prefix-list REDISTRIBUTION seq 5 permit 0.0.0.0/0 le 32 <<- this need change to 

ip prefix-list REDISTRIBUTION seq 5 permit 10.254.0.152/30 

this tune the static route redistribute, but again you need to add it under address family
try it without tag and check 

MHM

[MHM Cisco World]

any update ?

MHM