I'm trying to login for the first time to a vManage for some lab testing, setup by someone who has left our organisation.Credentials should be default admin/admin according to the info I have.GUI fails with these credentials, and when I SSH into the...
Forum Posts
Hello,Vedge2 device interface g0/0 is directly connected to interface e2/1 MPLS Router. There is no communication between the two devices. there's no MAC address learned by the Vedge device from the MPLS Router e2/1 interface. what could be the reaso...
Resolved! Cisco DNAC, KPI performance question
Good day,I've come today because I would like to use the report of DNAC to present how well my network perform with some KPI performance.What would be the most efficient way to do so, I've try generate some report but they just show basic information...
I had upgrade the SDWAN edge from 17.9.1 to version 17.12.1a. But after i reload the cegde to active new version the sig tunnel can not up seem autotracker not working on sig tunnel. Please advise with me workaround for this issue.
Hello ALL, I would like to seek advise, regarding on my SDWAN. It says that I have a connectivity issue, but per my checking my ISP connectivity to FW is okay. The dedicated public IPof the device is pingable. Also restart the device twice. Thank you...
My customer has power sustainability requirements and he wants to get the power consumption report from each SD-WAN device in the network. what would be the best way to do it? Cisco uses Crosswork Data and NSO to measure power consumption on Nexus 9k...
Hello braintrust! I have a problem that is related to configuring devices in vManage. As far as I can read/understand about the vManage API i should be able to change device-template on a device (effectively changing config) by using the following e...
Hi, I'm running some tests in my lab, on one of the site I'm try to implement a design involving both traditional routing and vEdges : On this pic, right now for the traditional part of the network, only SW3 and R1 are up and running with OSPF (ever...
Hello,I lost the connection from the vManage device, and I am unable to configure the default alternate route in the edge device. What is the option to detach the device from vManage to configure CLI mode?I decommissioned the wan edge4 in the device ...
Hello everyone,I've been attempting to retrieve ARP information from a Viptela vEdge device using SNMP, but haven't been successful. Specifically, I tried the following OIDs but did not receive any information:ipNetToMediaIfIndex: 1.3.6.1.2.1.4.22.1....
Hello,I'm unable to find the BFD and OMP sessions in the vedge7 device. VEDGE-7vEdge7# sh runsystemhost-name vEdge7system-ip 100.100.100.70site-id 70admin-tech-on-failureno route-consistency-checkno vrrp-advt-with-phymacorganization-name "viptela s...
Please advice what can be done to configure my cEdge. My cEdge router is currently unreachable and I am not able to detach it from device template nor can i make changes via CLI. Thanks in advanced. cEdge-30(config)# no ip route 0.0.0.0 0.0.0.0 10.1...
I have been looking for any documentation regarding Enhanced App-Aware Routing , bu there is none in the release note for 20.10, 20.11,20.12 nor in 17.10, 17.11, 17.12 that I could find. Anyone found any documentation regarding this new feature?
Resolved! SDWAN: redistribute ospfv3 into omp
hi guys, We have the following setup: C9300 <--ospfv3--> IR1101 (SDWAN Edge)<--omp-->ASR1000 (SDWAN Edge)<--bgp-->C9500 We were able to redistribute the bgp routes into omp and vice -versa. However, we couldn't do the same for ospfv3 into omp. omp in...
Hello, I have an SD-WAN setup where at one of our sites, we have a 500mbps (color green) and a 200mbps(color blue) circuit to the internet. We are currently doing some migrations from one site to another. I am attempting to create a policy that co...
