Resolved! Nexus 7000 M2 Module and OTV Support
Hello Guys,Can someone confirm if the M2 linecard will support OTV or not, I just cant find relevant information about this on Cisco website.Best RegardsMohammed Khair
Hello Guys,Can someone confirm if the M2 linecard will support OTV or not, I just cant find relevant information about this on Cisco website.Best RegardsMohammed Khair
Trying to create a custom RBAC role for Nexus 5500 SAN Admin. What role permission is required to have the ability to create device-aliases? The default san-admin role doesn't allow it so I created a custom role but can't figure it out.
Hello Guys,I found an interesting vPath behavior in VSG with ASA 1000v deployement on ESXi cluster. ASA 1000v have 2 interfaces only for data (Inside and Outside).When you want to enable the vPath for the ASA, you should apply vservice node type asa ...
I'm trying to connect a pair of Nexus 5532UP's, with vPC, to a Nexus 1000v. I'm running 4.2.1.SV1.4a. When I add the server's physical NICs to the dVS in vCenter, they fail to come up on the VSM and report link down (NoPortProfile). If I take "chan...
I have Cisco UCS C200 M2 with SAS 15K 450GB . When I put a bootable DVD the Server keeps giving me the following errorPXE-E61: Media test failure, check cablePXE-M0F: Exiting Intel Boot AgentReboot and select proper boot deviceor insert Boot Media in...
I have UCS B200M2 blades with following setup:blade 1 - ESXi 4.1 with primary N1k switchblade 2 - ESXi 4.1 with backup Nexus 1k switch and vCentre serverI shutdown the blade 2 servers gracefully and then rebooted blade 2 for UCS host firmware upgrade...
Can anyone tell me how I can access the "Capabilty Catalog" in a C220 M3 stand-alone environment?
Folks, I have a c series server connected to a nexus 7000 via the storage vdc using shared port. The c series does not have anything on it right now. I do not see any flogi information on my storage vdc. Any ideas would be highly appreciate...
hi guys,I have seen many examples of double sided vPC between one pair of N7k and one pair of N5k, I cannot see why it would not work between two pairs of N5k, could you confirm? any limitations?thanksming
Hi,We are using a Cisco Catalyst 3110X in a IBM Blade CentreUplink to a Nexus 5010.The Uplinks are 10GB using the Cisco X2-10Gb-SR modules.When we are doing large transfers (such as server builds) from the Netapp Filers to the Blade Servers we are ge...
hello ,we have two nexus connected in vPC with HP Flex-10 to the servers and connected to two firewall in cluster,that firewall will be the gateway for our servers,if the port channel between nexus and FLex-10 will be in trunk mode ,how will be the l...
I don't see any reference to L3 in the new linecard that Cisco just announced. Does anybody know if it is L2 only? Any other caveats that anybody knows of?
HII have a question about Cisco Nexus7000 switchRecently I found that one of our distribution switch (Nexus7k) was rebooted by itselfon the show version output, the reason of reboot was because of "Kernel Panic"What does that mean?? was it because of...
Hi ,I had a problem on FI and I needed to reinstall the N1k VEM, but before I had blade 1 -> esx1 -> module 1 and so on, now after a new install of VEM, I have the right information with sh module vem, but there are no logical , I...
Hello Nexus 1000V Gurus,Can someone help me with the correct process to restore a deleted 'primary' VSM. Any info would be much appreciated. Here's my story:I'm hoping someone can tell me where I went wrong with restoring a wiped Primary VSM.Primar...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 01-29-2026 10:05 PM | ||
| 10-03-2025 09:13 AM | ||
| 09-10-2025 01:24 AM | ||
| 12-30-2024 06:35 AM | ||
| 10-07-2024 09:53 AM |