Server Networking

We have a client who uses two CIP cards to connect to mainframe host via TCPaccess w/ GATED. Is it possible to use a logical address for the CIP instead of physical address for TCPaccess network configuration? Because we tried to use a logical addres...

I have a HOST with OS/390 and three OSA Fastethernetand I have define a VIPA. These Three OSA are conected to a 6500 (three differen ports).VIPA is a Virtual IP Adrres, that I can reach through any OSA adapter. How can I do if I wanted to balance IP ...

| |****** ******** | |* *--CPA1--*7206-1*--| ******** |*IBM * ******** |--*7206-3*--|* * | ******** |*HOST* | |* * ******** |--******** |* *--CPA2--*7206-2*--| *7206-4*--|****** ******** | ******** | | | 7206-1 and 7206-2 manage the the connection to...

Hi, When I configure ipx over frame-relay multipoint interface, I need to run eigrp and disable the split horizon, and I'm running ipx rip on the same router thus, redistribution is automatic by default. This will cause potential routing loop when th...

I have a 7200 router with a cpa interface. In show running config can be seen several interfaces channel(interface Channel2/0 no ip address no ip directed-broadcast ip mtu 0!interface Channel2/0 no ip address no ip directed-broadcast ip mtu 0)There i...

we hv 2mbps internet leased line...it was working fine and suddenly goes to very slower level..like a dialup connection...where do i find out what b/w i am getting at present?..Is it possible to view in router itself?..Sh int s0/0 ..shows 5 mins inpu...

Hi,I checked the cisco document, the tokenring switch 3900/3920 uses hexdecimal as the ring number, while the router tokering interface, it use demimal ring number, is there any in-consistancy? don't I need to convert them when doing configuration?Th...

I have 2 routers that have single escon connections to the same mainframe tcpip stack (os/390 2.9). What is the best way to provide failover from mainframe should one router fail. this involves mainly ibm tcpip configuration and would prefer to do wi...

How i can assign a different OSPF COST to differentVLANs if I am using a 6500? I can reach with IPusing OSPF an specific IPAddress through three different VLANS or ports. How can I do if I wantthat each different path has a diferent cost(weight).

What are the firewall auditing software needed for IDC setup..Monitoring s/w in Cisco..

Hello, Anyone have < Memorex Telex 1174> controller configuration menu ? Or where I can get ? ThanksRegardsJohn

Our main production is based on X25 network : SNA QLLC major part. We want to replace our 3745 (and NCP,NPSI), and we're planning toimplement a solution based in CISCO routers.Our actual configuration isHostIBM(S/390) ----> 3745 (with NPSI) ---> x.25...

Subject: SNA/QOSI AM CURRENTLY RUNNING 12.1(11a) IOS ON A ROUTER BASED NETWORK WITH FOUR7500 ROUTERS. I AM CURRENTLY RUNNING CUSTOMER QUEUEING AS MY QOS. I AMNOW LOOKING TO USING LLQ W/ CBWFQ AND DISTRIBUTED MODES, AS WELL. I HAVEVIP-40 CARDS IN ALL ...

I have an ethernet segment and a Token Ring segment.I have 2 routers connecting to both the Ethernet and the Token Ring. Both routers have a serial interface. I'm attempting to have dlsw redundancy for both Ethernet and Token Ring.I noticed that when...

Hello,I need a configuration about DLSw.The remote 1720 converts LLC2 -> QLLC (X25) over ISDN dial on demand connection to the central site.The central site accept the X25 call to forward it to an ES/9000 IBM.Thank you for your help, if you have any ...