Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hello all.We just bought ourselves 4 Nexus 9396 switches for 2 of our datacenters. When sitting and playing around with them im trying to get a FEX to be multihomed towards 2 of the Nexus 9k switches but it seems to be abit of a struggle. It will con...
Hi,
Recently, we got a problem with our Cisco server as it shutdown automatically and sometime it’s running in to error with a blue screen saying that some hardware not compatible.
After that we could not even log in to CIMC for few weeks but W...
Hello,I was collecting show tech from Nexus 7010 remotely, and I got disconnected (some temporary network issue). After reconnecting I am unable to collect show tech anymore. I get the message "Another show tech is running, please try again later". M...
I'm trying to enable the management port of Cisco UCS C 220. After booting up the server I pressed F8 to go to Cisco IMC configuration page. However, I ran into this password reset prompt before getting to the CIMC configuration (see attachment).
Af...
I have a client in the same building that would like to purchase 2Mb internet connection. I am handing off ethernet to this client from a port on my 3750. I need to limit this connection to 2Mb. I tried configuring srr-queue bandwidth limit 20, chang...
Hi,
Running two Cisco Catalyst 6506E in the VSS mode more than 4 years without any bugs. IOS Version 15.0(1)SY2
Suddenly after adding access-list (permit tcp host 192.168.0.xxx 17.0.0.0 0.255.255.255) Primary switch crashed, and with some delay up to...
I have a pair of 4500x running in vss mode. I would like to run Layer 3 port channel to a nexus 5548 pair running in vPC mode, IP address on portchannel interface on the 4500x pair only. Then nexus 5k would run Layer 2 vpc on same links connected to...
hi out there
all here are probably aware of this little note from vmware - http://packetpushers.net/vmware-kills-third-party-vswitches/ - and I am a bit in doubt about the consequence of this. As far as I can see this will also kill VSG - so we are l...
I'm looking for some guidance on assigning IP addresses to UCS-E. Can the CICM be on the same subnet as the kernel and the host? Is it required, or best practice, to have them on different subnets?
Any other thoughts or caveats?
I am attempting to delete a switch profile on my switches. I have two switches that use the switch profile. there is nothing in the buffer and the switches are in sync. when I go to delete the switch profile I get the following:
WARNING: Deleting...
Hi Guys,
Been having issues on one of our blade server
CIMC | Processor CATERR_N #0xd5 | Predictive Failure asserted | Asserted CIMC | Platform alert LED_BLADE_STATUS #0xf2 | LED color is amber | Asserted CIMC | Processor CATERR_N #0xd5 | Predictive...
Hi
I have a setup using Nexus 5K with 2K fexes. Default switchport state is active. I would like to change this with the command:
system default switchport shutdown
Im not sure what will happen to all the currently active ports - i cannot find any...
Hello,
I recently acquired a cisco MCS 7800 server to set up a call manager on. I have no idea where it came from and do not have a strong knowledge of servers. I have it connected with a VGA to a zero client (thin client) and cannot get a screen ...
I have N7K-F248XP-25E and N7K-M148GT-11L cards in a Nexus 7000 with the SUP2-E supervisors, Fab-2 (5) cards and 6.2(16) code. After inserting the F2E card it's giving me a "%VDC_MGR-2-VDC_UNALLOCATED: Module 4 is unsupported by the current vdc and s...
