Hi, I have some questions related to FTD as fusion device. (1) Ciscolive 2022 Las Vagas BRKSEC-2845 (see attached) shows two possible topology.- Direct FTD attachementDNAC can only provision L3 handoff using /30, not /29 or /28. Hence, if i do this, ...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
I tried to add catalyst 3560cx as an extended node to SDA fabric but I have this error message: Device tried to contact the server and failed during certificate_install how can I resolve this problem? is it possible to add extended node without using...
Hi,where can i find Visio Stencils, Shapes or Templates like the Graphics in the typical Cisco Live Presentations for the SDA-Family.it would be very practical to have the graphics from the presentations for DNAC, ISE, Border/Controlplane Node, Edge ...
Resolved! How to troubleshoot BUM multicasting?
HelloWe have an SD-Access infrastructure and L2-only vlan with PXE hosts. The FW is a DG for that VLAN and it connected thru L2 handoff.The problem is that PXE hosts can't boot for dozens of minutes after reloading the edge switch they are connected ...
Here is my question.... an example is if I have 5 states say California, Kentucky, Maryland, Utah and Florida. Can I manage them through DNAC from just one central site like Texas? Or do I need a separate ("3 DNACs)" equipment for each of the 5 ...
What's the correct way to do multi-tenancy in SD-Access? I haven't been able to find anything about it. Is it just using separate VN's? - but that doesn't seem like real multi-tenancy, as a single organisation/tenant could have multiple VNs for their...
Hi AllI m currently working on a solution to integrate an IP Phone ( SIP100) into the SDA network . I have successfully managed to authenticate and authorize the device via 802.1x through ISE but failing to obtain an IP address from the DHCP Server ...
Hi, I am reading this guide https://community.cisco.com/t5/networking-documents/how-to-cisco-dna-center-ise-integration/ta-p/3896410 on DNAC & ISE integration. (1) If i use self-signed in DNAC and ISE, just follow all the steps in the URL above and t...
Hi AllI m currently working on a solution to integrate an IP Phone ( SIP100) into the SDA network . I have successfully managed to authenticate and authorize the device via 802.1x through ISE but failing to obtain an IP address from the DHCP Server ....
I just updated AAA Server settings in the Network Settings for a site. How do I push that change to the devices assigned to that site? Nothing happens when I click save and device controllability is enabled. It says I either need to assign to a site ...
Hi I am going to study ACI, and we know its very expensive and hard lab to setup. Anyone can share some experience? I heard there is free lab in cisco. Not sure how it works. Thank you in advantage.
I want to use closed authentication on some ports in SDA environment so I've configured appropriate ISE authorization rules with SGT included. Authorization works fine but it seems EDGE switches are not aware of IP-SGT mappings. How EDGE switch could...
Hypothetically if my main fabric site has SDA platforms which supports up-to 64 VNs and then I decide to bring online a remote site with FiAB using say 9200's (which only supports up-to 4 VNs), what happens here if I have more than 4 VNs configured a...
Hi, I am new to IOT area, so need some advise from the community.Scenario - Green field setupSetup - SDA, ISE, DNAC.Logical topology (see attached) (1) The BMS has both server component and client component (DDC controllers).I will be connecting all...
I am designing a campus LAN infrastructure based on Cisco SD-Access solution. My end-customer campus consists of 6 buildings. In the current network, there is a couple of distribution switches in each building connected, with two fiber-optic links,...
