I have a customer who migrated their on-prem DC completely to public Cloud. Now they are interested about the SD-Access for their offices. As far as I know the DNAC is still only offered in physical hardware form factor, so does anyone know if there ...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Are you/your team using Cisco DNA Center to configure/monitor/manage SD-Access fabric networks? If so, we’d like to speak with you to get your feedback on some new concepts of a network management tool! We ask that you complete our brief surve...
Hey Cisco friends, Any chance you know what does it mean "Status Changed from No Status to Complete" ? I did some "Make a wish" request recently and I'm not sure if I'm interpreting this correctly after receiving an email notification from Cisco User...
Does any body knows what this Iisp error message means: Here as the error message and xtr and MS/MR_____________________________*Mar 20 07:16:10.462: LISP-0: Remote EID IID 0 prefix 10.165.155.11/32, Unable to get forwarding counters (sources: <map-r...
Resolved! What happens Smart Licenses expire.
Hello everyoneI use Catalyst 9000 series addition network-advantage and dna-advantage license.A license has expired one year. If I do not renew a license, what happens?
All of the SD-Access courseware always shows both the Non-Fabric and Fabric WLCs outside the Fabric.. basically beyond the Border node and sometimes outside but attached to the border node.So my question is if I have a CAT 9800 and I don't enable th...
Hello, In my understanding, ISE 'downloads' the IP-to-SGT mappings of the endpoints connected to the switch. This allows policy verification and permit/deny decision by the switch. Although rules and policies are configured between SGT's, the permi...
Hi all,I'm running DNAC ver 2.2.2.8 and after upgrading the DNAC to 2.2.2.8 I can't provision my fusion router (ISR4331, 16.12.05).The ISR4K was already configured and everything was working fine until the upgrade.The error I get is: Invalid configur...
Hello, How does Assurance define or update the “Inter-device Link” ports availability? One of the trunk ports seems to be down, and the device 360 health is reduced to 1/10. But i can verify that the trunk port informed is up all the time. Is there ...
Hi, I would like som clarification about certificates in DNAC 2.2.3.4.How can I replace the certificate for the admin-portal?Under System/Settings/Trust & Privacy/Certificates there is a button to replace certificate. Is this certificate only for the...
Dear Community, Kindly ask I have customer running ISE 2.7 and now they have purchased to us for SDA implementation but ISE 2.7 will be terminated and replaced with 3.x, my questions are below : 1. if they have run SDA with Cisco ISE 2.7 and next yea...
Resolved! Intermediate node SD Access
Hi, i have a question about the number of intermediate nodes in a SD Access fabric. Can i add two intermediate nodes behind each other? So you would get: Location A Border Node --> Location B Intermediate Node --> location C Intermediate node --> Loc...
Hi FolksDoes deleting the VNs and IP Pools associated to it from DNAC will remove related configuration from all devices ?How can we check what commands will be pushed to devices before DNAC start applying changes ? Is there a preview of commands ?
Register today. WAAS has been Cisco's WAN optimization solution for almost a decade now. However, with the fast-changing networks of today and the evolution of SD-WAN and Cloud deployments, it is important to transition to a solution that is built f...
Hello I am refering to the following URL however I can not understand yet. So I would like to ask how to configure the LISP routing for same segment. https://community.cisco.com/t5/networking-documents/lisp-fundamentals-and-troubleshooting-basics/ta-...
