Resolved! VSAN default is error-misconfigured
We are getting a "VSAN default is error-misconfigured" error. I noticed they are not using SAN options under UCS. They are only using LAN.How can I fix this? is it safe to change to another ID?
We are getting a "VSAN default is error-misconfigured" error. I noticed they are not using SAN options under UCS. They are only using LAN.How can I fix this? is it safe to change to another ID?
<Original post by Paoletto, replied by Jeremy. Moving from documents section to discussion section>Hello,We are unable to bring up the Cisco SFP+ twinax on a EMC VNX5300, it seems that this storage supports only active twinax cable (cisco 5m are pass...
Hello, Do we need to reboot the switch after I make changes to FC-Domain ID on Nexus 5K switch? Please let me know. Thank you!
hi, teamI have a question:I tried to add our MDS 9148 to DCNM but failed since there is firewall blocking.....so would you please let me knowwhich ports need to be open if adding MDS 9148 to DCNM for central managment? or if there is a reference docu...
hi all, I have two cisco 6513 sup 2T configured as VSS and I need to connect a UCS b-series to this VSS using two physically ports configured as port-channeli tried all modes of the port channel, no mode made the portchannel up except "mode passive" ...
When I use DCNM to discover a Nexus 5548, entering its mgmt0 address (172.16.x.190) as the seed, DCNM finds it but lists it as 1.1.1.190. It takes a long time to discover for some reason, too. When I open the fabric, it cannot access the switch unt...
Hello All Do we have an procedure to gracefully shut down the MDS-9513? Please advise ThanksChetan
due to a migration I've been doing a lot of port debugging recently. Just curious it seems like something gets cleared when I do disable , enable from device manager that does not happen when I do a int, shut no shut - am I dreaming this?
Hello All DCNM v6.2.3I see that the hosts are not logged-in to the switch, however via DCNM when I try to create device alias I find the pWWNs populated which are not logged-in. How are the pWWN list populated in DCNM even before they are logged-in t...
I am trying to connect two Cisco Nexus 5548UP switches together using GLC-SX-MMD with multimode fiber but link is still down. Set the interface speed to 1000 and swap the SFP to other slot but result is still down. Kindly help me. Output is belowSwit...
I want to install 10gig line cards on 6509 non-e chassis. Can anyone suggest me which model of line card i have to install?Does that line card model support my current SUP engine "WS-SUP720-3BXL"?How many line card this SUP engine can support?
Hi Team, Can anyone provide me the guideline on "how to configure tacacs+" on the above MDS switch. Thank you. Regards,Suthakar
Hi,I need to configure a QoS Policy for FCIP traffic going over 1GB circuits between three 6509's at three sites and then at each site at the core to distribution layer.I am hoping that the QoS policy can allow the FCIP traffic the majority of the ba...
I have a question about MDS 9509.I want to reload MDS 9509 contain two supervisor at the same time.Can I just use " reload" at the active supervisor?
Assisting our storage guys with some 9148s. We did a software upgrade from 5.0.1a to 5.2.8d. Now we do not see cdp adverts from the mgmt0 interface of the 9148s. Doing a sho cdp traffic int mgmt0 shows that the 9148s aren't even sending them, even th...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-20-2025 07:42 AM | ||
04-15-2025 01:46 AM | ||
03-15-2025 08:49 AM | ||
12-17-2024 08:07 AM | ||
10-25-2024 12:15 PM |