05-19-2008 06:38 AM - edited 03-05-2019 11:04 PM
I have a 3560 switch and I am getting the following error.
Base ethernet MAC Address: 00:1f:c9:96:60:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 452 files, 6 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 2176512
flashfs[0]: Bytes available: 13822464
flashfs[0]: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
done.
Loading "flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin"...flash:c3560-ipbase-mz.12
2-35.SE5/c3560-ipbase-mz.122-35.SE5.bin: no such file or directory
Error loading "flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
switch:
Can some one please direct me to a fix?
05-19-2008 08:16 AM
Make sure you mount the flash first.
flash_init
Then you can dir flash:/
Mark
05-19-2008 07:26 AM
Steve
I am confused. In a previous post we got this:
Hi Mahmood.
switch: dir flash:
Directory of flash:/
5 drwx 128
13822464 bytes available (2176512 bytes used)
switch:
and now it appears that the dir command is not recognized. Has something changed on the switch?
The previous dir command shows that this is a directory: c3560-ipbase-mz.122-35.SE5. If you get the dir command to work again it would be helpful to see the output of
dir flash:c3560-ipbase-mz.122-35.SE5/
that might indicate whether your boot image is really there or not.
HTH
Rick
05-19-2008 07:29 AM
Hi Rick,
its the . at the end of flash not a : as it should be.
Andy
06-16-2008 11:24 AM
Steve,
I read through this thread, and I hope that you were able to get the problem resolved.
The problem appears to be that the image file that the switch was trying to load was not located in the directory it was pointed to. Newer Cisco devices (including the C3560) put the image file in a subdirectory with the same name as the image, so it can be confusing.
Note that this is not a requirement for the image file to be in a separate subdirectory, and that the easiest way to remedy this is to re-format the flash media and put the image file in the root directory of the flash media.
In any case, simply following the password recovery procedure for this switch would allow you to specify from rommon which image to load. It's a manual process, but it is the direct process, and does not rely on you putting boot information into the configuration file and relying on the switch to read the configuration file to determine where the boot image is.
Hope this helps (you or someone reading through this archive someday...)
Ron Buchalski
06-16-2008 11:46 AM
Hi Ron,
Yes thanks to all the replies I found a fix in X-MODEM. I am now up and running again.
Steve.
06-16-2008 12:04 PM
So, your co-worker ended up blowing away the IOS imge and not installing any image on the switch?
I did that the first time I tried to upgrade the IOS on the 3560. I had deleted the existing image from flash (via format flash: command), and inadvertently rebooted the switch befor I put another IOS image on it.
And yes, I also had to deal with x-modem.
Glad to hear that you resolved ths issue.
Ron Buchalski
06-16-2008 04:41 PM
Myself I just delete the directory and use the .bin file its easier if you don't need gui function .
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide