Hi, I intend to deploy a pair on 93180YC switches, connected to these will be a fex each. Does the 93180YC support VPC+ ? ta tim
Hi, I intend to deploy a pair on 93180YC switches, connected to these will be a fex each. Does the 93180YC support VPC+ ? ta tim
Hello All,I have a question regarding connecting a 3560 switch I have to a Linksys WRT54G router. Since the 3560 doesn't have NAT, what I would like to do is use the Linksys as my NAT router and then have a different subnet on my 3560 to separate it...
I have network on picture and can't ping hosts each other. I've set RIP. Topology and output of "show ip route" are in attachment. I think that problem is in addresses I've set on serial links between routers, because when I change that IP addresses ...
I want to use router-on-a-stick method on cisco 2600 , after creating a sub-interface, can not use "encapsulation" command to define encapsulation method and it's vlan .How to correct this that can use "encapsulation" command ? The IOS version is 12....
Hello guys, I'm quite new to Cisco & networking. I have a brand new Cisco ASA 5506-X that I want to configure to go to the internet. So i used ASDM to configure the router. The local network is 192.168.107.0 /24 so Inside interface is 192.168.107...
Hello,I am new to QoS and trying to implement an end to end QoS specifically for real-time voice for traffic coming from our Cisco 7841 VoIP Phones, which is EF (DSCP 46).Our network flow is as follows:IP Phone - Cisco 2960S Access Switch (L2) - Cisc...
Hello,I have a SG350XG-24F, currently running the latest firmware (2.3.5.63)What would be a normal timing for rebooting the switch ? Mine is currently doing that in 10-12 minutes, which seems awfully slow... (2-3 minutes before losing ping to the OOB...
I have version ns-os 7.X (and v 5.x) and trying to enable the ldap feature. It is listed as disabled in the feature but when I try to enable it "feature ldap" , it does not exist. Documenation says there are no special license requirements to enable ...
I have a 4500 Switch and a Nexus 7K. The 4500 switch rebooted due to a bug in the IOS and when it came back up the OOB connection on it stayed down. This OOB is connected via a fiber link to my 7K. When I run a "speed nonegotiate" command on the Ca...
Hi, I have small lab where I am attempting to roll out a Citrix Xendesktop environment with Netscaler VPX. In order to finish, I need to allow my Cisco SG300-28 layer 3 switch provide a route to the internet. I dont know if this is possible but t...
Recently, I had a chance to ask some questions to the CCIE holder. I asked few questions that have been bothering me most. He gave me answers, but he told me that he is not 100% sure. If you know the correct answer, please comment :) 1. When I asked ...
1 half-duplex systems 2 Full-duplex systems 3 Wireless system what collison avoidance mechanism are they using ? csma/cd oe csma/ca
Hi all, i have Cisco core 4507 with Ten GB interface , i want to connect this interface with Multi mode fiber connection to an edge switch that have 1GB interface , both interface are up but there is no connectivity between two switches , when exe...
Dear all, i am trying to learning PBR my topology is mentioned above i am using EIGRP and i have two gateways one is 256k and other is 512K so eigrp choose 512K as high bandwidth. so now i am tyring to do is that if pc pings to ip 22.22.22.22 it ...
hi, I need to setup an acl for Vlan blocking. i have configured vlan 10 & vlan 20. what is my requirement is vlan 10 should not communicate to vlan 20 but from vlan 20 should communicate with vlan10 i have created a extended access list like this...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-01-2024 04:28 AM | ||
09-27-2024 06:10 AM | ||
09-25-2024 01:15 PM | ||
09-17-2024 12:44 AM | ||
09-13-2024 03:59 AM |
User | Count |
---|---|
8 | |
8 | |
6 | |
6 | |
5 |