Buy or Renew
Buy or Renew

Switching

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! Mgig?

Hey anyone know when 3850s will have mgig abilty? If they don't all ready? Having a hard time finding any info on it.  Thanks

Cisco 4500X Auto QoS on EtherChannel interfaces

Hello, We are attempting to port-channel on 4500X trunk interfaces with Auto QoS and encountered the following errors as described here: http://blog.lah.io/2013/10/cisco-catalyst-4500-x-etherchannel-auto.html): 4500X(config)#int range te1/15-16 450...

mwhite1983 by • Beginner
  • 2099 Views
  • 1 replies
  • 0 Helpful votes

Fetch TV & Cisco 877 IGMP/Streaming

Hi Guys,Hoping someone could help me, I'm trying to configure my Cisco 877 ADSL border. It uses the ATM interface to talk to the ADSL. The fetch TV uses Multicast IP streams for the "on demand" TVHere is my config:version 15.1no service padservice ti...

Resolved! Tunneling VLAN though L3

Hi GuysPlease see attached diagram for my topology.I have a primary and back sites both are about a mile apart. Both sites now have a link going out and I want to failover traffic to the backup site when the primary external link fails.Now the ISP ha...

Mokhalil82 by • Enthusiast
  • 510 Views
  • 9 replies
  • 0 Helpful votes

Binding MAC address with IP address

Dear all. In our environment we have all the servers and computers assigned with Static IPs. But the problem is users are assigning IPs by themselve without our permission. This is causing us lots of head ache.  So what we are thinking is to Bind Mac...

cisco WS-C6513 cpu high

Hi all ,give me some insight from the process below . is the hike is high or normal ?sh processes cpu | ex 0.00%CPU utilization for five seconds: 38%/24%; one minute: 38%; five minutes: 38% Sw2sh processes cpu | ex 0.00%CPU utilization for five secon...

susim by • Participant
  • 234 Views
  • 2 replies
  • 0 Helpful votes

Unsupported SFP+ in C3KX-NM-10G

Is there any way to "force" the even ports of C3KX-NM-1G as 10G ports?  The idea is to make "service unsupported-transceiver" work for 3rd party SFP+ transceivers (I'm guessing there's not enough info in the optics' EEPROM to have it detected as 10G,...

Resolved! Switch throughput..how much to expect.

While troubleshooting a slowness issue, I connected 2 laptops directly to a 3750-48 port switch. One made a http web file server and folder shared and started downloads and file copy on the other. Download rate that i got was of 18MBytes(144Mbits/sec...

CPU utilization high on 3560

Hi all ,cpu spiking up to 90-100% , Does it solve the issue if we upgrade the firmware "c3560-ipservicesk9-mz.122-55.SE9" .Current firmware is "flash:/c3560-ipbasek9-mz.122-55.SE7/c3560-ipbasek9-mz.122-55.SE7.bin" ------------------------------------...

susim by • Participant
  • 1699 Views
  • 7 replies
  • 0 Helpful votes

4510 - I'm losing pings to thin clients and pdu units when i bring up a new truck in the network

All,on my 4510, I have about 36 vlans and 40+ trunks(Cisco 3650, 3750, 2960) on my campus, lately when i bring up a new trunk i lose pings to  smaller devices like a PDU mgmt port or thin client or even a printer which some are directly connected to ...

vartanian by • Beginner
  • 138 Views
  • 1 replies
  • 0 Helpful votes

QoS DSCP to Output Queues

I'm using a 3560X-24P running 12.2(55)SE5 IPBase. I should be getting a lot more packets queued into my queue 2 than I am and I'm not sure why I'm not.  Any help would be appreciated as it makes it very hard to properly allocate buffers if the packet...

PolyCaleb by • Beginner
  • 259 Views
  • 3 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers
Spotlight Award Nomination