Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
I'm trying to find the hardware installation guide for the Catalyst 1300 series. All I can find is this web-based "wizard" that wants to lead me by the hand. Is there no HIG PDF for this product like there is for pretty much every other Cisco devic...
Resolved! VLAN Mapping NXOS
Hi, how can I do a simple vlan mapping on a nexus 9000 like I can do on a 9200L? From the 9200L docs: Device(config)# interface HundredGigE1/0/1 Device(config-if)# switchport mode trunk Device(config-if)# switchport vlan mapping 10 20 Thanks!
Hi all, I'm kinda to my wits end about this one, as I do know that NTP can be setup when you use express setup when the switch is new out of the box. However I can't find any source or material to change any of the configuration, like NTP, when the d...
HiWe have Cisco Nexus 93180YC-FX switches. All ports are currently used and additional servers are required to be connected.Can I make use of the breakout cables that are available.I.e the switches have 6 x 40/100-Gbps QSFP28 ports.If I used a QSPF-4...
Resolved! C9200L Config Not Saving on Reboot
Hi,I'm trying to set up a C9200L-24T-4X-E-RF switch. I'm setting it up using the following commands but it seems the configuration is not being saved between reboot.switch: boot flash:/cat9k_lite_iosxe.17.03.05.SPA.binSwitch>enableSwitch#config tSwit...
Does C1100 family switch h/w support LACP (802.3ad)?
Hello, Software upgrade hangs on EXTRACT: Extracting the image. How that happened: "I wanted to install an update on the device WS-C2960X-48FPS, using the well-known command archive download-sw /reload ftp://lic:lic@10.10.10.10/c2960x-universalk9-tar...
TL;DRWe have trunks between two datacenters, with stretched vlans, that put were in place for DC migration and were never cleaned up completely. Does it matter? I work on a large enterprise network that, once upon a time, shifted its on-prem datacent...
I need to convert a two switch 9300_48p stack to a two switch 24p stack. Can i just do a more or less cut n paste?What about this line crypto pki certificate poolcabundle nvram: *****Can i copy that as well?What other bits will I need to change or c...
Hello, For WAN switch access, I have connected cable from CORE to WAN switch with trunk configuration on both the ports.I am able to get ping and SSH access from core switch and access switches, but not getting ping and SSH access from end device(L A...
I have two catalyst 9200 line switches, one c9200-24P-E and one c9200-48P-E, is it possible to stack between them forming a single switch stack?
Hello there,A while ago, we wanted to update all our switches to a more recent firmware version (17.9.5) with Catalyst Center. While doing that, we encountered an issue, on a few stacks, where a switch of those stacks wouldn't have enough space on it...
Hi,I'm having the same problem where the switch is not delivering the correct power wattage for IP cameras.When the PTZ camera connected to C1300, switch is delivered 8 watts onlyWhen Fixed camera connected to C1300, switch is delivered 3 watts onlyW...
Hi We have ordered some 9200Cx, but it seems that we need a micro USB to get to the console. Not the standard mini USB type B, but the mobile phone type USB Micro Type B.A standard USB Micro Type B, doesn't work, even with the Cisco USB Driver, not s...
Hello, I am trying to resolve the new CVE for snmp issues: CVE-2025-20352. I used the tools provided and encountered this issue. I am on Version 03.07.04E and the tool says to go to 3.11.13E for the fix. However I cannot find that in Downloads Home>S...
