Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
Resolved! mixed stacking C9300
Hello friends I have a question, can I do stacking between 9300-48t-a and 9300-24s-a? If that is possible, then I understand that they must have the same licensing level, but I could do a stack between 9300-48t-a and 9300-24s-e. I saw some Advantage ...
Hello, since a few weeks, we are notice a lot of timeouts in our network. We figured out that there are unplanned reboots in our stack. This is what the stack is logging: We are using the stack in a ring-topology in hybrid-mode with the firmware 2.5....
Hello Cisco Community,I'm currently facing a communication issue with my network setup involving three Cisco IE-9300 series switches. Here's a brief overview of my configuration:Switch A: Configured as a Layer 2 switch for LAN-A.Switch B: Configured ...
I need Distribution Switch With this Same Specifications I am Unable To chose Exact By comparing please Help your Suggestion?20 x 100M/1G/2.5G/5G/10G Base-T Ethernet PoE ++ ports• 16 x 10GE SFP+ Port (Modules: 6 x 10 Gig Multi mode optical SFP+)• 2 x...
Resolved! 6500 to Nexus Design Question
Greetings. Basic question here --- I have two 6500 Core switches setup with HSRP, however, they are not VSS. They are two separate switches. Downstream I need to connect two Nexus 9k's. My plan: On the Core side, two ports in chassis 1 setup as a LA...
Hi all, I have tried accessing my cisco 3850 switch via winscp but was not able to list the directory. My authentication works fine but it just doesn't show the directory listing on my winscp. Objective is to upload IOS to my cisco 3850. Pls advise...
Resolved! Dynamic Access list
is there anything called Dynamic access list ? if yes ,for what purpose is it used ?
If I have a layer 3 switch acting as my PIM enabled multicast router for SSM multicast, with a directly connected downstream layer 2 switch also supporting IGMPv3 and I plug in a device such as a Cisco phone that only supports IGMPv2, can I still mak...
Resolved! how to configure ssh in catalyst 1300
Hi engineers how can i configure ssh in catalyst 1300 please do not paste traditional cmd because it has different os
Resolved! DHCP Not Working
When I try to create a DHCP pool with a specific network it will automatically change the final part of my IP address to a 0e.g. network 193.13.32.8 255.255.255.224will become:network 193.13.32.0 255.255.255.0Above is a copy of my network. i have loo...
With stacked switches, we set the higher priorities on the switches that have the trunks to the core. Is there any benefit to assigning a priority to the other stack members? As an example, if it is three stacked switches, we would assign them: SW1...
all, i am running into a few problems with netconf on cat9k platforms. I'm trying to add these into dnac but when i enable netconf-yang, i am seeing the following:Mar 5 01:16:42.051: yang-infra: ERROR: Failed to create a trustpoint usable for NETCONF...
Hello Everyone, The picture is my C1300-24XS connection status, I find when I link up the copper to the port-21, port LED is not light up the circle-1 instead is circle-2. when I link up the copper to the circle-2's port-21, the port LED is light up...
Dear Friend,Please find the below Loop avoidance mechanism.Loop avoidance mechanism on EIGRP:Secondary Ad< Primary FDLoop avoidance mechanism on BGP:EBGP:Verify the AS number, If the AS no. is the part of it's own As no. then It will reject the packe...
After updating my Cisco 9200l from 16.12.04 to 17.13.01 I cannot access the webui. I get an error message that says "SSL_ERROR_INTERNAL_ERROR_ALERT".
