Cisco 3550 to 3524 - Cisco Community

3304

Views

0

Helpful

15

Replies

Hello,

I have these 2 switches Cisco 3550 to 3524 as a test lab and I have set the 3550 up as the core\routing.

I want to trunk and talk between them but I cant get them talking, I've followed this:

http://www.ciscopress.com/articles/article.asp?p=29803&seqNum=3

Switch configs are below, 3524:

Building configuration...

Current configuration:

!

version 12.0

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname Switch

!

!

!

!

!

!

!

ip subnet-zero

!

!

!

interface FastEthernet0/1

!

interface FastEthernet0/2

!

interface FastEthernet0/3

!

interface FastEthernet0/4

!

interface FastEthernet0/5

!

interface FastEthernet0/6

!

interface FastEthernet0/7

!

interface FastEthernet0/8

!

interface FastEthernet0/9

!

interface FastEthernet0/10

!

interface FastEthernet0/11

!

interface FastEthernet0/12

!

interface FastEthernet0/13

!

interface FastEthernet0/14

!

interface FastEthernet0/15

!

interface FastEthernet0/16

!

interface FastEthernet0/17

!

interface FastEthernet0/18

!

interface FastEthernet0/19

!

interface FastEthernet0/20

!

interface FastEthernet0/21

!

interface FastEthernet0/22

!

interface FastEthernet0/23

!

interface FastEthernet0/24

!

interface GigabitEthernet0/1

!

interface GigabitEthernet0/2

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 1-100,1002-1005

switchport mode trunk

!

interface VLAN1

no ip directed-broadcast

no ip route-cache

!

interface VLAN5

ip address 10.1.5.10 255.255.255.0 <<<<<<<<<<<<< My Management VLAN

no ip directed-broadcast

no ip route-cache

shutdown

!

!

line con 0

transport input none

stopbits 1

line vty 0 4

login

line vty 5 15

login

!

end

Switch#

----------------------------------------------------------------------------------------------------------------------------

3550:

bmi-c3550-core#show running-config

Building configuration...

Current configuration : 2675 bytes

!

version 12.1

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname bmi-c3550-core

!

!

ip subnet-zero

ip routing

!

!

spanning-tree mode pvst

spanning-tree extend system-id

!

!

!

interface FastEthernet0/1

no switchport

ip address 200.1.1.1 255.255.255.0

!

interface FastEthernet0/2

switchport access vlan 2

switchport mode dynamic desirable

!

interface FastEthernet0/3

switchport access vlan 3

switchport mode dynamic desirable

!

interface FastEthernet0/4

switchport mode dynamic desirable

!

interface FastEthernet0/5

switchport mode dynamic desirable

!

interface FastEthernet0/6

switchport mode dynamic desirable

!

interface FastEthernet0/7

switchport mode dynamic desirable

!

interface FastEthernet0/8

switchport mode dynamic desirable

!

interface FastEthernet0/9

switchport mode dynamic desirable

!

interface FastEthernet0/10

switchport mode dynamic desirable

!

interface FastEthernet0/11

switchport mode dynamic desirable

!

interface FastEthernet0/12

switchport mode dynamic desirable

!

interface FastEthernet0/13

switchport mode dynamic desirable

!

interface FastEthernet0/14

switchport mode dynamic desirable

!

interface FastEthernet0/15

switchport mode dynamic desirable

interface FastEthernet0/16

switchport mode dynamic desirable

!

interface FastEthernet0/17

switchport mode dynamic desirable

!

interface FastEthernet0/18

switchport mode dynamic desirable

!

interface FastEthernet0/19

switchport mode dynamic desirable

!

interface FastEthernet0/20

switchport mode dynamic desirable

!

interface FastEthernet0/21

switchport mode dynamic desirable

!

interface FastEthernet0/22

switchport mode dynamic desirable

!

interface FastEthernet0/23

switchport mode dynamic desirable

!

interface FastEthernet0/24

switchport mode dynamic desirable

!

interface GigabitEthernet0/1

switchport mode dynamic desirable

!

interface GigabitEthernet0/2

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 1-100

switchport mode trunk

!

interface Vlan1

no ip address

shutdown

!

interface Vlan2

ip address 10.1.2.254 255.255.255.0

!

interface Vlan3

ip address 10.1.3.254 255.255.255.0

!

interface Vlan4

ip address 10.1.4.254 255.255.255.0

!

interface Vlan5

ip address 10.1.5.254 255.255.255.0

!

interface Vlan6

ip address 10.1.6.254 255.255.255.0

!

interface Vlan7

ip address 10.1.7.254 255.255.255.0

!

interface Vlan8

ip address 10.1.8.254 255.255.255.0

!

interface Vlan9

ip address 10.1.9.254 255.255.255.0

!

interface Vlan10

ip address 10.1.10.254 255.255.255.0

!

ip classless

ip route 0.0.0.0 0.0.0.0 200.1.1.2

ip http server

!

!

line con 0

line vty 5 15

!

end

-------------------------------------------------------------------------------------

What am I missing?

15 Replies 15

Which interfaces are you connecting together?

On int vlan 5 do a "no shut" then you should be able to ping to the other switch interface on vlan5

Sent from Cisco Technical Support iPad App

Right i've applied the no shut to vlan 5 on the edge which I cannot ping the edge switch still:

nterface VLAN5

ip address 10.1.5.10 255.255.255.0

no ip directed-broadcast

no ip route-cache

shutdown

I can now ping all vlans!

any idea still on the switch ip?

Also if I try and ping any default gateway from the core I get this:

Switch#ping 10.1.2.254

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.1.2.254, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

Switch#

Hi HGAED,

You don't seem to have a default gateway applied to the 3524, so it gets packets from your PC in the 10.1.2.0/24 network but doesn't know where to send it back.

Give that switch a default gateway of 10.1.5.254 and the 3524 will know where to send the icmp reply.

ip default-gateway 10.1.5.254

HTH

Jonathan S

Thanks Jonathan,

I've now applied that command, the output:

Switch#

Switch#ping 10.1.5.254

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.1.5.254, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

Switch#

Ok at this point let's make sure it's not a L1 or L2 problem.

Do a show int gi0/2 on both switch to make sure they are both in an up/up state.

Jonathan S

3524:

Switch#show int gi0/2

GigabitEthernet0/2 is up, line protocol is up

Hardware is Gigabit Ethernet, address is 0008.a391.d2da (bia 0008.a391.d2da)

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive not set

Auto-duplex (Full), 1000Mb/s, media type is CX_GIGASTACK

output flow-control is off, input flow-control is off

ARP type: ARPA, ARP Timeout 04:00:00

GigaStack module(0.2) in GBIC slot. link1 is down, link2 is up

Last input 00:00:11, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 3000 bits/sec, 4 packets/sec

180 packets input, 18037 bytes, 0 no buffer

Received 57 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 52 multicast, 0 pause input

3558 packets output, 275150 bytes, 0 underruns

0 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 pause output

0 output buffer failures, 0 output buffers swapped out

3550:

bmi-c3550-core#show int gi0/2

GigabitEthernet0/2 is up, line protocol is up (connected)

Hardware is Gigabit Ethernet, address is 000f.34b3.949a (bia 000f.34b3.949a)

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 1000Mb/s, link type is auto, media type is CX Gigastack

output flow-control is off, input flow-control is off

ARP type: ARPA, ARP Timeout 04:00:00

GigaStack module(0.2) in GBIC slot. link1 is up, link2 is down

Last input 00:00:00, output 00:00:04, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 4000 bits/sec, 7 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

46120 packets input, 3455979 bytes, 0 no buffer

Received 44939 broadcasts (0 multicast)

0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 43134 multicast, 0 pause input

0 input packets with dribble condition detected

2750 packets output, 308592 bytes, 0 underruns

0 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 PAUSE output

0 output buffer failures, 0 output buffers swapped out

bmi-c3550-core#

-----------------------------------------------------------------

From my laptop with static IP 10.1.2.5 I can ping all vlan gateways, from core I can ping laptop fine.

From core I cannot ping 10.1.5.10 which is the VLAN5 and IP of edge switch

Thanks for helping, I'm more a ProCurve man!...

Issue "show interface trunk" on both switches, do you see your vlans on the trunk?

from 3550:

bmi-c3550-core#show interface trunk

Port Mode Encapsulation Status Native vlan

Gi0/2 on 802.1q trunking 1

Port Vlans allowed on trunk

Gi0/2 1-100

Port Vlans allowed and active in management domain

Gi0/2 1-8,10

Port Vlans in spanning tree forwarding state and not pruned

Gi0/2 1-8,10

bmi-c3550-core#

bmi-c3550-core#

from 3524:

When I plum the command into the 3524 I get this:

Switch#show interface trunk

^

% Invalid input detected at '^' marker.

Switch#

OK, try this instead on the 3524 show int gi0/2 switchport

Done from 3524

Switch#show int gi0/2 switchport

Name: Gi0/2

Switchport: Enabled

Administrative mode: trunk

Operational Mode: trunk

Administrative Trunking Encapsulation: dot1q

Operational Trunking Encapsulation: dot1q

Negotiation of Trunking: Disabled

Access Mode VLAN: 0 ((Inactive))

Trunking Native Mode VLAN: 1 (default)

Trunking VLANs Enabled: 1-100,1002-1005

Trunking VLANs Active: 1-8,10

Pruning VLANs Enabled: 2-1001

Priority for untagged frames: 0

Override vlan tag priority: FALSE

Voice VLAN: none

Appliance trust: none

Switch#

-----------------------------------------------------------------------

Interesting from 3524, I cannot ping any gateways or laptop, but the laptop is connected to the 3524 and can ping gateways

Try shutting down vlan 1 on the 3524, make sure vlan 5 is enabled and ping again

Getting somewhere now, I did have this:

interface VLAN5

ip address 10.1.5.10 255.255.255.0

no ip directed-broadcast

no ip route-cache

shutdown

ran the no shutdown command on int vlan 5 and its come alive now!

Looks like I can ping everything between switches.

Looking at both switch configs in the top post is there anything else I need todo or any recommended commands?

For the 3524, I would say to assign the user ports to a vlan of your choice using the "switchport access vlan " and still shutdown the interface vlan1.

Learn, share, save

Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.

New here? Get started with these tips. How to use Community New member guide

Log in to Community

Review Cisco Networking for a $25 gift card