Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Hi alli could do with some advice, we need to use MFA when logging into our Cisco switches. We currently use windows radius.ive tried setting up duo but cant get it to work, also tried the entra ID plugin on the windows radius server, that also fails...
Hi,few month ago 17.15.5 turned to be the recommended IOS-XE version and now with these vulnaibility there should be an upgrade from it. what do you recommend and advise? 17.18.4, 17.15.6 or anything ?https://sec.cloudapps.cisco.com/security/center/c...
hi all,getting this error when i insert a USB flash drive in a cisco switch dir usb1:usb is either not present or not formatted or not mountedive tried FAT and FAT32, only tried one make thothanks,rob
If I need a Catalyst-level L2 switch with an enterprise-level configuration, the specifications should be approximately 16 ports. It doesn't require SFP ports or PoE. Are there any recommended models that meet these needs?
just to ask if ever the way of configuring the switches and router's will ever fade away since well there is a way to configure the switches and router via the scripts ,and that leave wondering if we have to know the programming language also or stil...
Hello Team, I hope you're doing well.I'm currently working with a Cisco Catalyst 9604R running IOS XE 17.15.5 and equipped with a C9600-LC-24C line card.After enabling SNMP for monitoring, our monitoring platform (Zabbix) automatically discovers the ...
Hey there,I am trying to create a stackwise virtual setup with 2 x C9500-24Y4C through the meraki dashboard.When i am connecting my 2 interfaces dedicated for the SVL and 1 interface for the DAD, STP kicks in and blocks the 3 ports on the 9500-2 then...
To free up the QSFP port of the 9400 supervisor module I need to move our existing/production DAD link down to the lower half of ports. Is this as simple as removing the config from the existing port and moving it to the new port? Does anyone know if...
Hi, could I get a 3D CAD Model of your Catalyst 3560-CX Series 12-port PoE switch (Model No WS-C3560CX-12PD)? I would like to import the switch model into my system assembly. Thanks.
I have a C9500-48Y4C IOS XE 17.12.4 that is notifying of a lot of MAC flapping. This is the typical error log. Oct 27 13:14:41.253: %SW_MATM-4-MACFLAP_NOTIF: Host 0050.56b1.96a0 in vlan 412 is flapping between port Twe1/0/3 and port Po1When the switc...
Hello,I would like to confirm whether the GLC-FE-100LX SFP transceiver is compatible with a Cisco Catalyst WS-C3750X-24T-S equipped with a C3KX-NM-1G 4-port SFP network module.Our requirement is a 100 Mbps Single-Mode fiber connection.The GLC-FE-100L...
I bought a Cisco Catalyst switch from a hamfest (amateur radio swap meet) and am trying to get it working. I am a retired software engineer and am just looking to get this working. I can connect to it through a serial conection and can run some ini...
one of the 2960X switch in stack of 5 switches booted with new IOS and other with old IOS only when boot varibale is set with new IOS and strange thing is still connected in stack and whole stack working properly
I have two sites that are a bit further than 10KM and are using Cisco C9300X to replace the Meraki MS425. We installed a Cisco QSFP-40G-ER4 but they don't seem to work. It was suggested we use a native Meraki optic, but looking at the Meraki website...
need cad model C9200L-48T-4X-E. Thank you!
