The following log message was output on Catalyst 9400 version 17.12.5.Is it safe to ignore this log?What does each log mean, what is the cause, and what is the recommended action? %FMFP-3-OBJ_DWNLD_TO_DP_STUCK: F0/0: fman_fp_image: AOM download to Da...
Forum Posts
I'm a new user of Cisco products in a public transportation agency and I'm working with both the Cisco 819 and 829 routers. These devices are installed on a large fleet of vehicles.We have written procedures for setting up both models, but the engine...
Greetings,I have aquired a second hand WS-C3650-8X24UQ-S. Appears to be working as is (connected to router and one pc), and no password. When looking up reset instructions, I see typically you flash_init, then delete config.text and vlan.dat (after h...
good morningI have several Cisco 3560-CX 12 and 16 port switches. when using IPv4 we simply used the command "show ip device tracking all" to find the IP for each device when troubleshooting but there does not seem to be an IPv6 equivalent. I found s...
Hi Cisco timI would like to ask about the compatibility matrix of the Cisco Nexus C93180YC-FX3 with the SFP-10G-T-X transceiver. I plan to use 32 or more units of the SFP-10G-T-X transceiver on a single Cisco Nexus C93180YC-FX3 device.My question is:...
I’m looking for the EU Declaration of Conformity for the CISCO1921/K9. I specifically need a separate document in the standard format. We’ve received an official request from the authorities. Links to "cae-cnc-prd.cisco.com" are not sufficient — thi...
Hi,May I ask if there is any way to deploy my own class-map into the default system-cpp-policy?I’m trying to restrict SSH connections to only one loopback address, and have all other IPs dropped.On basic routers, I achieved this using an extended ACL...
Resolved! Password 6 setup for cisco 9200l
Hello Cisco community, I have a Cisco 9200L. For some reason, we have had no luck migrating from password 7 to password 6. Each time I attempt config, it gives me an error. I even tried a new switch for additional testing, but still gives same re...
Resolved! Cisco IE2000 and SD Card
I have a Cisco IE2000 and I have a project I want to use SD Cards for config deployment. Can anyone tell me which SD cards I can use that aren't Cisco branded? The one 1gb SD card I tried to use gives me the normal, "Warning: Non-IT SD flash detect...
Hello everyone,I'm currently testing two Catalyst 9606Rs, each with two supervisor engines.In 'show module' I see the assignment as follows:Switch 1:Slot 3= Active, Slot 4= ICSActive= sso, ICS=rprSwitch 2:Slot 3= Standby, Slot 4= ICSActive= sso, ICS=...
Hi Team,Users in my network are receiving bad IP addresses, and our DHCP scope is set up on a Microsoft Windows Server.Please assist me in resolving this issue and let me know if you need any information from my side.
Hi everyone,I'm currently monitoring a Cisco Catalyst 9200 switch running IOS XE 17.12.x using PRTG via SNMPv2.SNMPv3 is also configured and used for other monitoring purposes.Basic sensors like ping, uptime, CPU, and memory are working fine. However...
Hi All,Hope you can help. I currently have a 2 switch stack (C9200L-24P) I need to add a switch and have the same model switch which I have changed the SW version to match (17.6.5) but have noticed the new switch is HW Version 06 while the stack swit...
Hello,Can we configure SSO/NSF betweent two 9500 paired using StackWise virtual and each having a single RP?
Is it correct that the Catalyst 9200CX switches are not supported in Cisco Prime Infrastructure? I could not find the devices in the compatibility matrix of the latest Prime version (3.10) or anywhere else. Is the support planned in a future update a...
