10-22-2020 11:05 PM
Hi ,
I'am extending my home internet connection to separate room as Wifi is not reachable over there ,So my setup is something like this , ISP Router > Cisco Switch >Cisco AP1131AG .
ISP ethernet cable is terminating on Cisco port 24 ( fas 0/24 ) ,
AP is a non POE so it's getting power from the Cisco Switch and connected on fas 0/23
ISP DG is 192.168.0.1
Can anyone advise what config I need for this set up ,any help much appreciated .
10-23-2020 12:01 AM
If you did not configure the switch then it will be default VLAN 1 - or you like to change you can if the switch acting like Layer2 here.
So i would leave it as it is and test it. ( check to make sure ports are up and running when you connect devices to cisco switch).
Configure your AP workgroup bridge mode.
https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/68472-configure-wgb-00.html
10-23-2020 12:28 AM
Hi ,
Thanks for your reply , do I need to configure any DG in switch or AP ?
I can see the AP is broadcasting the SSID and I can connect to it , but still I'am not able to access to internet .
10-23-2020 12:33 AM
if the AP acting as bridge mode, it is transparent till ISP router.
if your PC configured as DHCP ISP router able to give an IP addres ?
if not configure your PC
192.168.0.100
255.255.255.0
gateway - 192.168.0.1
DNS 8.8.8.8
test
10-23-2020 01:08 AM
Yes , PC is configured as DHCP .. Please see the config below for switch and AP , Many Than
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.10.23 09:02:28 =~=~=~=~=~=~=~=~=~=~=~=
sh run
Building configuration...
Current configuration : 1266 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
system mtu routing 1500
ip subnet-zero
!
!
!
!
!
--More-- !
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
--More-- !
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
--More-- interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
no ip route-cache
!
ip http server
--More-- ip http secure-server
!
control-plane
!
!
line con 0
line vty 5 15
!
end
Switch#
Switch#sh ip inter bri
Switch#sh ip inter brief
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned YES unset up up
FastEthernet0/1 unassigned YES unset down down
FastEthernet0/2 unassigned YES unset down down
FastEthernet0/3 unassigned YES unset down down
FastEthernet0/4 unassigned YES unset down down
FastEthernet0/5 unassigned YES unset down down
FastEthernet0/6 unassigned YES unset down down
FastEthernet0/7 unassigned YES unset down down
FastEthernet0/8 unassigned YES unset down down
FastEthernet0/9 unassigned YES unset down down
FastEthernet0/10 unassigned YES unset down down
FastEthernet0/11 unassigned YES unset down down
FastEthernet0/12 unassigned YES unset down down
FastEthernet0/13 unassigned YES unset down down
FastEthernet0/14 unassigned YES unset down down
FastEthernet0/15 unassigned YES unset down down
FastEthernet0/16 unassigned YES unset down down
FastEthernet0/17 unassigned YES unset down down
FastEthernet0/18 unassigned YES unset down down
FastEthernet0/19 unassigned YES unset down down
FastEthernet0/20 unassigned YES unset down down
FastEthernet0/21 unassigned YES unset down down
--More-- FastEthernet0/22 unassigned YES unset down down
FastEthernet0/23 unassigned YES unset up up
FastEthernet0/24 unassigned YES unset up up
GigabitEthernet0/1 unassigned YES unset down down
GigabitEthernet0/2 unassigned YES unset down down
Switch#
*Mar 9 22:13:21.888: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
ap>
*Mar 9 22:13:25.518: %DOT11-6-DFS_SCAN_COMPLETE: DFS scan complete on frequency 5520 MHzen
Password:
ap#sh run
Building configuration...
Current configuration : 1440 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$pBmH$DUSfkSNc.KKJHAF0aDHD1.
!
no aaa new-model
ip domain name addm.ads.brm.pri
!
!
!
dot11 ssid OPEN
authentication open
guest-mode
!
power inline negotiation prestandard source
!
!
username Cisco password 7 1531021F0725
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
ssid OPEN
!
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
no ip route-cache
!
ssid OPEN
!
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
no ip address
no ip route-cache
!
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end
*Mar 9 22:14:01.312: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 6cab.317b.6f14 Reason: Sending station has left the BSS
*Mar 9 22:14:01.320: %DOT11-4-MAXRETRIES: Packet to client 6cab.317b.6f14 reached max retries, removing the client
10-23-2020 01:11 AM
I will review the config later -
what is the oout come : configure your PC
IP 192.168.0.100
subnet - 255.255.255.0
gateway - 192.168.0.1
DNS 8.8.8.8
are you able to ping 192.168.0.1 ?
10-23-2020 01:33 AM
I'am not able to ping 192.168.0.1
10-23-2020 02:09 AM
Looks like you have basic config on radio and also required switch side Trunk port.
make sure you associated radio config with ssid
below exmaple :
10-23-2020 02:22 AM
Switch#sh run inter fas 0/24
Building configuration...
Current configuration : 87 bytes
!
interface FastEthernet0/24
description ****ISP Link****
switchport mode trunk
end
_________ *** AP Radio Config ***
ap#sh run inter do
ap#sh run inter dot11Radio 1
Building configuration...
Current configuration : 329 bytes
!
interface Dot11Radio1
no ip address
no ip route-cache
!
ssid OPEN
!
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
end
ap#sh run inter dot11Radio 0
Building configuration...
Current configuration : 297 bytes
!
interface Dot11Radio0
no ip address
no ip route-cache
!
ssid OPEN
!
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
end
10-23-2020 02:55 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide