Hello all,Can anyone explain why RSTP does not have forward delay timers, and what are the port transitioning states.
The content you are looking for has been archived. View related content below.
Hello all,Can anyone explain why RSTP does not have forward delay timers, and what are the port transitioning states.
I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
Also sorry, english isn't my native language so I tried to translate the assignment as best as I could.I only managed to do the DHCP server & I am not sure if I did it correctly or not. Because I tried other things like doing the ethernet channel but...
Im having issuse with coping the Class and QOS commands form my old 3560 Switch to the 9300x switch
Hi, I have a client who is using the command "vlan dot1q tag native" on their Catalyst switches (causing all packets even on the default VLAN to be tagged and require tags), and Meraki MX105 firewalls. Packets leaving the MX105s are tagged on all VLA...
Hello,Can we configure SSO/NSF betweent two 9500 paired using StackWise virtual and each having a single RP?
Hello Cisco community, I have a Cisco 9200L. For some reason, we have had no luck migrating from password 7 to password 6. Each time I attempt config, it gives me an error. I even tried a new switch for additional testing, but still gives same re...
Am getting a little obssed over networking over the last few days and decided to go for ccna and i started learning and reached ACL ,specifically extended ACLs ,but when i was trying a hands on in CPT i got stuck . since i dont have a proper mentor i...
This morning, I found that the C9115 AP led light connected to the C9300L-24P-4X switch blinks red-green-blue cyclically, and I checked the POE switch and found that the poe status of the port connected to the AP is down, but I can see that the inter...
I recently got an IEM-16P expansion module for an IE-3300-8P2S and cannot get it to pass POE. I've tried the expansion module on two separate 3300 base switches with the same result. With a 48VDC 480W power supply I can power an IE-3300-8P2S with an...
Recently need to upgrade C9407 Current version: 16.12.03aTarget version: 17.9.6a Supervisor 1 XL Module with 25G FW: 16.12.2rCPLD: 19032905 Two 9407 SVL units---Can't find the upgrade path in official documentation?Can we upgrade directly from 16.12...
Hi guys .The SOC administrator in my department told me that, for the purpose of securing the network, I should disable the password recovery service so that no one can access the switch configurations just by having a console cable. But I’m not sure...
I'm a new user of Cisco products in a public transportation agency and I'm working with both the Cisco 819 and 829 routers. These devices are installed on a large fleet of vehicles.We have written procedures for setting up both models, but the engine...
I checked the following document and found that “ACLs cannot be configured on management ports.” but we confirmed that it is possible to configure it on the actual device at Is this an error?interface GigabitEthernet0/0 ip access-group 111 in ip acce...
Good morning team, how can I access the web on a WS-3650? I've already created users via SSH and it opens properly, but I can't log in via the web.Could you help me?Thank you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM | ||
05-23-2025 10:30 AM |
User | Count |
---|---|
11 | |
9 | |
8 | |
6 | |
5 |