cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1167
Views
0
Helpful
12
Replies

PA-MC-8T1 on FlexWan in 6500

yogi
Level 1
Level 1

I cannot get the PA-MC-8T1 to work on our 6509-NEB. See the flexwan module ok but not the PA, IOS is 12.1(27b) so I am ok there. I am wondering if it is an issue with not being supported by the SUP1A-2GE. Any help would be appreciated.

1 Accepted Solution

Accepted Solutions

Yes, correct, flexwan is hot swappable, PA might be not. Most time, I just suggest customer to pull out flexwan when replacing PA.

View solution in original post

12 Replies 12

Yudong Wu
Level 7
Level 7

In "show diag", did you see PA-MC-8T1?

Show diag below, flexwan is in slot 7, looks like it does see it in Bay 0???

Thanks

C6509#show diag

Slot 7: Logical_index 14

FlexWan controller

Board is analyzed ipc ready

HW rev 1.3, board revision B0

Serial Number: SAD04320GD6 Part number: 73-3869-07

Slot database information:

Flags: 0x2004 Insertion time: 0x240BAD44C (16:46:01 ago)

Controller Memory Size:

56 MBytes CPU Memory

8 MBytes Packet Memory

64 MBytes Total on Board SDRAM

IOS (tm) cwlc Software (cwpa-DW-M), Version 12.1(27b)E, RELEASE SOFTWARE

(fc2)

PA Bay 0 Information:

Multi-channel (T1) PA, 8 ports

EEPROM format version 1

HW rev 1.00, Board revision A0

Serial number: 23119576 Part number: 73-2488-07

Slot 7: Logical_index 15

FlexWan controller

Board is analyzed ipc ready

HW rev 1.3, board revision B0

Serial Number: SAD04320GD6 Part number: 73-3869-07

Slot database information:

Flags: 0x2004 Insertion time: 0x240BAC474 (16:46:08 ago)

CWAN Controller Memory Size: Unknown

But "CWAN Controller Memory Size: Unknown" does not sound right. Can you try to reseat both PA and flexwan? You can try Bay 1 as well.

I reset both of them just a day or so ago. Bay 1 has a supervisor module. I have bays 3 - 6 available, does it matter which bay?

flexwan has two slots, we call it bay 0 and bay 1. You can put PA in another slot of flexwan if possible.

OK, I got you. I understand the PA is not hot swap so I need to pull the whole flexwan, correct?

Yes, correct, flexwan is hot swappable, PA might be not. Most time, I just suggest customer to pull out flexwan when replacing PA.

That looks like it did it! So just a bad bay perhaps?

Could be.

If you don't mind, you can try to put it back to bay 0 again. If it still has issue, you need to replace flexwan.

Looks like it is still good moved back to bay 0????

C6509#show diag

Slot 7: Logical_index 14

FlexWan controller

Board is analyzed ipc ready

HW rev 1.3, board revision B0

Serial Number: SAD04320GD6 Part number: 73-3869-07

Slot database information:

Flags: 0x2004 Insertion time: 0x244CC31B4 (00:13:20 ago)

Controller Memory Size:

56 MBytes CPU Memory

8 MBytes Packet Memory

64 MBytes Total on Board SDRAM

IOS (tm) cwlc Software (cwpa-DW-M), Version 12.1(27b)E, RELEASE SOFTWARE

(fc2)

PA Bay 0 Information:

Multi-channel (T1) PA, 8 ports

EEPROM format version 1

HW rev 1.00, Board revision A0

Serial number: 23119576 Part number: 73-2488-07

Slot 7: Logical_index 15

FlexWan controller

Board is analyzed ipc ready

HW rev 1.3, board revision B0

Serial Number: SAD04320GD6 Part number: 73-3869-07

Slot database information:

Flags: 0x2004 Insertion time: 0x244CC23C0 (00:13:31 ago)

Controller Memory Size:

56 MBytes CPU Memory

8 MBytes Packet Memory

64 MBytes Total on Board SDRAM

IOS (tm) cwlc Software (cwpa-DW-M), Version 12.1(27b)E, RELEASE SOFTWARE

(fc2)

That's why I asked you to try it again in bay 0. :)

I guess that it might not be seated well.

hmmm. OK well thanks for the help!

Review Cisco Networking for a $25 gift card