10-14-2019 12:00 AM
HI Everyone,
Thesedays, we are occuring a issue that is "show inv" command cannot display full info of two cat6500 device in VSS mode.
We have done some steps on VSS before,
First, we power down all cat6500 device(chassis1 is the active role,and chassis 2 is the secondary one).Then, we power on the chassis1, and power on chassis2 after it boot complete.Finally, we can see the VSS mode normal by "show switch virtual" command, it shown as below:
C6K-SW01#show switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 100
Local switch number : 1
Local switch operational role: Virtual Switch Active
Peer switch number : 2
Peer switch operational role : Virtual Switch Standby
Conversion completed : No
Perform exec command 'switch accept mode virtual' to complete the VSS conversion
There is the problem,we cannot get the full info by "show inv" in chassis1,we can only see some module on chassis2,but we cannot find any info about chassis1,just like this:
C6K-SW01#show inventory
NAME: "Chassis 2 WS-C6509-E", DESCR: "Chassis 2 Cisco Systems, Inc. Catalyst 6500 9-slot Chassis System"
PID: WS-C6509-E , VID: V05, SN: SMCXXXXXXXX
NAME: "Chassis 2 WS-C6K-VTT-E 1", DESCR: "Chassis 2 VTT-E FRU 1"
PID: WS-C6K-VTT-E , VID: , SN: SMTXXXXXXXX
NAME: "Chassis 2 WS-C6K-VTT-E 2", DESCR: "Chassis 2 VTT-E FRU 2"
PID: WS-C6K-VTT-E , VID: , SN: SMTXXXXXXXX
NAME: "Chassis 2 WS-C6K-VTT-E 3", DESCR: "Chassis 2 VTT-E FRU 3"
PID: WS-C6K-VTT-E , VID: , SN: SMTXXXXXXXX
NAME: "Chassis 2 CLK-7600 1", DESCR: "Chassis 2 OSR-7600 Clock FRU 1"
PID: CLK-7600 , VID: , SN: SMTXXXXXXXX
NAME: "Chassis 2 CLK-7600 2", DESCR: "Chassis 2 OSR-7600 Clock FRU 2"
PID: CLK-7600 , VID: , SN: SMTXXXXXXXX
NAME: "Chassis 2 1", DESCR: "Chassis 2 WS-X6704-10GE CEF720 4 port 10-Gigabit Ethernet Rev. 3.1"
PID: WS-X6704-10GE , VID: V03, SN: SALXXXXXXXX
NAME: "Chassis 2 WS-F6700-CFC Centralized Forwarding Card EARL sub-module of 1", DESCR: "Chassis 2 WS-F6700-CFC Centralized Forwarding Card Rev. 4.1"
PID: WS-F6700-CFC , VID: V06, SN: SALXXXXXXXX
NAME: "Chassis 2 Transceiver Te2/1/1", DESCR: "Chassis 2 Transceiver 10Gbase-LRM Te2/1/1"
PID: XENPAK-10GB-LRM , VID: V01 , SN: AGAXXXXXXXX
NAME: "Chassis 2 WS-C6509-E-FAN 1", DESCR: "Chassis 2 Enhanced 9-slot Fan Tray 1"
PID: WS-C6509-E-FAN , VID: V03, SN: DCHXXXXXXXX
NAME: "Chassis 2 PS 1 WS-CAC-3000W", DESCR: "Chassis 2 AC power supply, 3000 watt 1"
PID: WS-CAC-3000W , VID: V01, SN: AZSXXXXXXXX
NAME: "Chassis 2 PS 2 WS-CAC-3000W", DESCR: "Chassis 2 AC power supply, 3000 watt 2"
PID: WS-CAC-3000W , VID: V01, SN: AZSXXXXXXXX
Do you know what wrong with this ?
10-14-2019 12:39 AM
show inventory should show all, try another command as below
show module switch all
10-14-2019 01:11 AM
10-14-2019 06:13 AM
I am running code Version 15.2(1)SY3
show inventory on Cat 6509-E with VSS shows both the switches.
10-14-2019 06:51 AM
10-15-2019 04:32 AM
Hi
Use "Show inventory raw" command in privilege mode, if it works,
Please rate helpful.
Thanks.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide