WS-C2950-24 - Web Page Access

brian.stivala · ‎05-12-2012

Hi All,

I have a cisco C2950 and I've just did a firmware upgrade. I have downloaded the

c2950-i6q4l2-tar.121-22.EA14.tar and I've installed the firmware accordingly. Everything went well, the Switch is booting with new version etc..etc..

The problem I have is that when I try to access from the web, I can't see anything. The command for the http is enabled as well.

As per hereunder is the show version of the C2950

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA14, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Tue 26-Oct-10 10:35 by nburra

Image text-base: 0x80010000, data-base: 0x80570000

ROM: Bootstrap program is C2950 boot loader

Switch uptime is 8 minutes

System returned to ROM by power-on

System image file is "flash:c2950-i6q4l2-mz.121-22.EA14.bin"

cisco WS-C2950-24 (RC32300) processor (revision Q0) with 20956K bytes of memory.

Processor board ID FOC0844Y05B

Last reset from system-reset

Running Standard Image

24 FastEthernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:12:7F:46:DB:80

Motherboard assembly number: 73-5781-13

Power supply part number: 34-0965-01

Motherboard serial number: FOC08440CJA

Power supply serial number: DAB0843JSQP

Model revision number: Q0

Motherboard revision number: A0

Model number: WS-C2950-24

System serial number: FOC0844Y05B

Configuration register is 0xF

Flash Directory As per herunder

Directory of flash:/

2 -rwx 110 Mar 01 1993 00:15:09 +00:00 info

3 -rwx 314 Mar 01 1993 00:21:02 +00:00 env_vars

4 -rwx 616 Mar 01 1993 00:24:32 +00:00 vlan.dat.renamed

6 -rwx 3132319 Mar 01 1993 00:17:11 +00:00 c2950-i6q4l2-mz.121-22.EA14.bin

8 drwx 4480 Mar 01 1993 00:17:54 +00:00 html

90 -rwx 110 Mar 01 1993 00:18:54 +00:00 info.ver

91 -rwx 1131 Mar 01 1993 00:02:16 +00:00 config.text.renamed

93 -rwx 5 Mar 01 1993 00:02:16 +00:00 private-config.text.renamed

Top upgrade the Firmware I 've used this link which was very pretty straight forward.

http://www.dslreports.com/faq/10854

Thank

Regards

Brian Stivala

amikat · ‎05-14-2012

Hi,

Will you please make sure you have the enable password configured as this is the default method of HTTP server user authentication. Should you decide you can configure other HTTP server interface authentication method via the "ip http authentication" command.

Best regards,

Antonin

brian.stivala · ‎05-15-2012

Hi Amikat,

Thanks foir your reply,

I've already did that, I've manage to solve that by upgrading another firmware E10A crypto and without any setting whatsover I've managed to have web access. If I'm not mistaken the http access is on by default. So I dont know why with E14 firmware didn't work. The funny side is that while I was working with web base on version E10A, from the web I've decided to upgrade once again to E14 and it works.Now I'm using the latest firmware version and the latest Cisco SDM.

Kindly let this discussion open so people can solve their issue that I had.

Thanks,

Brian Stivala

glen.grant · ‎05-14-2012

Check this out.

http://www.cisco.com/en/US/docs/ios/12_2/configfun/command/reference/frf005.html

brian.stivala · ‎05-15-2012

Hi Glen,

Thanks for your reply,

Check my reply to Amkat as per above and see what I did to solve the issuel.

Thanks

Regards,

Brian Stivala

itdAbbas · ‎09-28-2023

I cannot get the iOS any help with the file?