TelePresence and Video Infrastructure

i encounter a problem.in a service provider network,the network manager config two ip address on a ethernet port.i config the pim sparse mode on this ethernet port and specify rp address for this router.the router connect layer 2 switch directly.but...

Hello allI'll like to connect a live sorce to the brance CE or IP/TV 34xx or to som STB , Can any body hekp in how ? Regard Ofer Eliel

I bought the IPVC-3544-CHAS, IPVC-3540-MC03A,IPVC-3540-AS,IPVC-3540-DS03 for my Callmanager.I'm looking for some step-by-step instructions from Cisco on adding the Polycom Viewstations.I assume I give the Polycom's fixed ip addresses, the register th...

Hi All,I have the following config to give priority to my video endpoint on the LAN with an IP Precedence 4. This is assuming that my ISP has QoS set on the WAN Edge router on the MPLS cloud (I do not have access to this router). Here is my config.Sw...

Hi ALL,I want to set up my LAN for QoS to prioritize Video Over IP. I have 2 sites across an mpls WAN. Each site has a cisco router and l2/l3 3750 Cat switch. I do not have access to the ISP routers, the ISP does. On the Cat switch at both ends I pla...

hello.i have ccm and cme.ccm has one ip phone ( number is 1000)cme has one ip phone ( number is 2000)i configured below.but it does not call each other.dial-peer voice 555 voipdestination-pattern 2000session target ipv4: 192.168.0.1 --> cme gatewa...

Dear all,I want to Block Video over IP by Access-list in Cisco Router. Can anybody help me over this.Please tell me which TCP or UDP Ports I have to block for this. So that I can completely remove data access to and from Video over IP.Regards,Tushar

I have a Cisco Call Manager 3.3 Server... I'm getting a 2600 Router with a WIC-1DSU-T1 card. Briefly tell me what else I need in terms of hardware in order to test Call Manager using Tapi programming tools, and connect to 2 dial up phone lines and my...

1. H.323 & SIP support2. distributed call platform integrated gateway/ controller3. STU/ FNBDT relay over IP4. support for both legacy TDM & VoIPIs anyone familiar with Network Equipment Technologies, Inc. SHOUTip platform??

I am at a complete loss. Cisco want 800 USD to help me.I need to setup Direct Outward Dial on my CME 3.1 (3725). I need to have one of my two POTS lines show up on the telephones mapped to a button.I have searched for quite a while, and tried most ...

Is there a white paper or some set of instructions for setting up CM 4.0 as a gatekeeper with equipment other than Cisco?I have a Tandberg gateway and want to use CM as the gatekeeper but I'm told that the configuration must be done properly.I also u...

Hi,we have CCM 4.0(2)a 7940 Phones with Firmware 6.5one some phones, not always, but very often we can not dial to any external DN out of personal address book, missed calls , placed calls , except calls.It does not work with different DN out of di...

Hi,We have a VOIP problem. The sympton are :1. The HQ router call to each remote site are ok, except one of branch office, when HQ router call to this branch office, branch office will received the ring, but if pick up the phone, no voice heard.2. Th...

My local FXS card is connected to my office PBX CO port. When a far end caller disconnects a VoIP session, my local FXS generates a very strange tone to my PBX so that the AA of my PBX cannot detect such busy tone and hence cannot drop the call. The ...

Anyone ever run it on XP ? We are running it, but I have a strange error when I click on serverwatch. Everything else seems fine.