AIM-CUE keep rebooting issue

cooltreedan · ‎07-13-2013

Hi everyone,

Please help my AIM-CUE module, it keep rebooting again and again, that happens when I found it not booting correct, and tried to install from boot helper mode, the boot helper installation didn’t successful, because it’s just rebooted, not like normally boot helper installation.

First, when I from the router, I reset the module, IF I DIDN’T DO ANYTHING, the CUE module it’s just keep rebooting again and again, here’s the output:

Router#service-module service-Engine 0/1 reset

Use reset only to recover from shutdown or failed state

Warning: May lose data on the the NVRAM, nonvolatile file system or unsaved configuration!

Do you want to reset?[confirm]

Trying to reload Service Module Service-Engine0/1.

From the CUE, I got:

Initializing memory. Please wait. ...

*Jul 13 22:53:11.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration:

*Jul 13 22:53:31.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to upFound disk 0

found 1 drives

root cmd : root (hd0,0)

Filesystem type is reiserfs, partition type 0x83

kf: a1 : /bzImage root=/dev/hda1 ro plat=aim

kf: a2 : /bzImage root=/dev/hda1 ro plat=aim

in grub_open: /bzImage root=/dev/hda1 ro plat=aim

in grub_open1: /bzImage root=/dev/hda1 ro plat=aim

in grub_open2: /bzImage root=/dev/hda1 ro plat=aim

in grub_open3: /bzImage root=/dev/hda1 ro plat=aim 1

in grub_open4: /bzImage root=/dev/hda1 ro plat=aim

kernel_func: kt: 0

Unable to load image

in boot func: kt: 0

Unable to boot image

Initializing memory. Please wait. ... 256 MB SDRAM detected

BIOS

*Jul 13 22:53:51.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration:

*Jul 13 22:54:11.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to upFound disk 0

found 1 drives

root cmd : root (hd0,0)

Filesystem type is reiserfs, partition type 0x83

kf: a1 : /bzImage root=/dev/hda1 ro plat=aim

kf: a2 : /bzImage root=/dev/hda1 ro plat=aim

in grub_open: /bzImage root=/dev/hda1 ro plat=aim

in grub_open1: /bzImage root=/dev/hda1 ro plat=aim

in grub_open2: /bzImage root=/dev/hda1 ro plat=aim

in grub_open3: /bzImage root=/dev/hda1 ro plat=aim 1

in grub_open4: /bzImage root=/dev/hda1 ro plat=aim

kernel_func: kt: 0

Unable to load image

in boot func: kt: 0

Unable to boot image

Initializing memory. Please wait.

*Jul 13 22:54:21.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down... 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration:

*Jul 13 22:54:41.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to upFound disk 0

found 1 drives

root cmd : root (hd0,0)

Filesystem type is reiserfs, partition type 0x83

kf: a1 : /bzImage root=/dev/hda1 ro plat=aim

kf: a2 : /bzImage root=/dev/hda1 ro plat=aim

in grub_open: /bzImage root=/dev/hda1 ro plat=aim

in grub_open1: /bzImage root=/dev/hda1 ro plat=aim

in grub_open2: /bzImage root=/dev/hda1 ro plat=aim

in grub_open3: /bzImage root=/dev/hda1 ro plat=aim 1

in grub_open4: /bzImage root=/dev/hda1 ro plat=aim

kernel_func: kt: 0

Unable to load image

in boot func: kt: 0

Unable to boot image

Initializing memory. Please wait. ...

*Jul 13 22:55:01.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration:

*Jul 13 22:55:21.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to upFound disk 0

found 1 drives

root cmd : root (hd0,0)

Filesystem type is reiserfs, partition type 0x83

kf: a1 : /bzImage root=/dev/hda1 ro plat=aim

kf: a2 : /bzImage root=/dev/hda1 ro plat=aim

in grub_open: /bzImage root=/dev/hda1 ro plat=aim

in grub_open1: /bzImage root=/dev/hda1 ro plat=aim

in grub_open2: /bzImage root=/dev/hda1 ro plat=aim

in grub_open3: /bzImage root=/dev/hda1 ro plat=aim 1

in grub_open4: /bzImage root=/dev/hda1 ro plat=aim

kernel_func: kt: 0

Unable to load image

in boot func: kt: 0

Unable to boot image

Initializing memory. Please wait. ... 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...

*Jul 13 22:55:41.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down[BOOT-ASM]

Please enter '***' to change boot configuration:

And it just keep rebooting forever, and you can see the Interface Service-Engine0/1 keep flapping, up and down, up and down.

Second, same from the router, I reset the module, IF I HIT “*” TO GET IN THE BOOT-LOADER MODE, AND I WANT TO RE-INSTALL THE IMAGE**, I got the following output:

Initializing memory. Please wait.

*Jul 13 23:01:41.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down... 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration: ***

ServicesEngine Bootloader Version : 2.1.14

ServicesEngine boot-loader>

*Jul 13 23:02:01.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to up

ServicesEngine boot-loader> config

IP Address [192.168.1.6] >

Subnet mask [255.255.255.0] >

TFTP server [192.168.1.2] >

Gateway [192.168.1.5] >

Default Helper-file [cue-installer.nm-aim.3.2.5] >cue-installer.nm-aim.3.2.5

Default Boot [none|disk] [disk] >

Default BIOS [primary|secondary] [primary] >

Default bootloader [primary|secondary] [primary] >

Updating flash with bootloader configuration

1.2.3.4.5.6.7.8.9.10.11.12.done.

ServicesEngine boot-loader>

ServicesEngine boot-loader> boot helper

nw_boot: 0 cue-installer.nm-aim.3.2.5

Me: 192.168.1.6, Server: 192.168.1.2, Gateway: 192.168.1.5

Loading cue-installer.nm-aim.3.2.5

Dbg: Final image size: 11466076

Debug: bl_sz: 95040

Debug: cisco_bl_sz: 59694

0x0000007f 0x00000045 0x0000004c 0x00000046 0x00000001 0x00000001 0x00000001 0x

00000000 0x00000000 0x00000000

cisco_cl_addr: 0x1001930

Debug: bl_sz: 95040

Debug: cisco_bl_sz: 59694

0x0000007f 0x00000045 0x0000004c 0x00000046 0x00000001 0x00000001 0x00000001 0x

00000000 0x00000000 0x00000000

loader_addr: 0x1200000

Cisco BootLoader start

verify_netboot_img

found signature

Found bootable

img_start: b sig_len: 172 sig_start: 5

bl_sz: 95040

Cisco_bl_sz: 59694

after buf_len: 4256

after KEY_InitMem

reading key: 0

reading key: 1

reading key: 2

reading key: 3

reading key: 4

reading key: 5

after aesop_RSA_keyarray_read

in verifysignature_md5, MD5 hash generated now, str format:hexmd5:005e374ebde6699317c76f8a6b94a790

Verifying signature now...

calling RSA decrypt now

mem ptr: 0 704 832 968 1040 1172 1184 1196 1208 1220 1228 1244 1268 1284 1300 1316 1332 1344 1360 1384 1400 1664 1804 2080 2224 2364 2880 3396 3660 3924 4188 RSA decrypt returned:4294967295

verifysignature_md5, Orig MD5 hash generated during encryption:蘔躓#墼]?^7N芥i?莖妅敡?

calling RSA decrypt now

mem ptr: 0 704 832 968 1040 1172 1184 1196 1208 1220 1228 1240 1260 1276 1288 1304 1320 1332 1348 1368 1380 1644 1784 2060 2204 2344 2860 3376 3640 3904 4168 RSA decrypt returned:33

verifysignature_md5, Orig MD5 hash generated during encryption:005e374ebde6699317c76f8a6b94a790

signatures match...

Image signature verified successfully

CISCO_BL: boot_image: 0x1200000

[LOADER]: image/plat/sz: 2/0/11466076

Aesop Helper: system image header: v=2, b=946332, i=10516786

Network boot: moving 3072 code bytes to 0x90000

....

Network boot: invoking kernel now

[BOOT-PHASE2]: booting kernel

Linux version 2.4.24 (bld_adm@bld-system) (gcc version 2.95.3 20010315 (release)) #1 Fri Mar 30 08:37:07 PST 2007

Platform: aim

setup.c: handling kernel log buf at [126.5MB]

setup.c: handling trace buf at [127MB]

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009f800 (usable)

BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 0000000007e80000 (usable)

BIOS-e820: 0000000007e80000 - 0000000007f00000 (reserved)

BIOS-e820: 0000000007f00000 - 0000000008000000 (reserved)

BIOS-e820: 0000000008000000 - 0000000010000000 (usable)

BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)

256MB LOWMEM available.

On node 0 totalpages: 65536

zone(0): 4096 pages.

zone(1): 61440 pages.

zone(2): 0 pages.

DMI not present.

Kernel command line: root=/dev/ram ramdisk_size=200000 ramdisk_start=0x6000000 console=ttyS0,9600n8 plat=aim

Initializing CPU#0

Detected 298.895 MHz processor.

Calibrating delay loop... 596.37 BogoMIPS

Memory: 244896k/262144k available (1211k kernel code, 15324k reserved, 693k data, 96k init, 0k highmem)

in atrace_init

log_head: h: 2138328399, t: 317757402, l: -1738732095, w: -28157, s: 221072279

Initializing trace buffer

log_head: h: 0, t: 0, l: 0, w: 0, s: 1047488

Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)

Inode cache hash table entries: 16384 (order: 5, 131072 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)

Page-cache hash table entries: 65536 (order: 6, 262144 bytes)

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 128K

CPU: Intel Celeron (Coppermine) stepping 0a

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

PCI: PCI BIOS revision 2.10 entry at 0xe5f7d, last bus=0

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Probing PCI hardware (bus 00)

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

kinoded started

VFS: Disk quotas vdquot_6.5.1

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: devfs_debug: 0x0

devfs: boot_options: 0x1

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

Cisco ContentEngine Flash Driver Version 0.02

RAMDISK driver initialized: 16 RAM disks of 200000K size 1024 blocksize

eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html

eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others

eth0: PCI device 8086:1209, 00:04:9A:49:3C:70, IRQ 10.

Receiver lock-up bug exists -- enabling work-around.

Board assembly 668081-002, Physical connectors present: RJ45

Primary interface chip i82555 PHY #1.

General self-test: passed.

Serial sub-system self-test: passed.

Internal registers self-test: passed.

ROM checksum self-test: passed (0xdbd8681d).

Receiver lock-up workaround activated.

Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

PIIX4: IDE controller at PCI slot 00:07.1

PIIX4: chipset revision 0

PIIX4: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio

ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio

hda: STI 2d408003171218, CFA DISK drive

blk: queue c03210c0, I/O limit 4095Mb (mask 0xffffffff)

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

hda: attached ide-disk driver.

hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }

hda: task_no_data_intr: error=0x04 { DriveStatusError }

hda: 2001888 sectors (1025 MB), CHS=993/32/63, DMA

init unit number == 0

Partition check:

/dev/ide/host0/bus0/target0/lun0: p1 p2

Model == STI 2d408003171218

Flash capacity == 2001888

init unit number == 1

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 2048 buckets, 16Kbytes

TCP: Hash tables configured (established 16384 bind 16384)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

RAMDISK: Compressed image found at block 100663296

Freeing initrd memory: 10270k freed

VFS: Mounted root (ext2 filesystem) readonly.

Mounted devfs on /dev

Init flash stats for STI 1GB wear_planes=16

Init flash stats

Freeing unused kernel memory: 96k freed

INIT: version 2.86 booting

Started device management daemon v1.3.25 for /dev

/dev/ide/host0/bus0/target0/lun0: p1 p2

mount: mount point /dev/pts does not exist

mounting sys fs ...

mount: unknown filesystem type 'sysfs'

/dev/root has gone 38480 days without being checked, check forced.

1067 inodes used (17%)

12 non-contiguous inodes (1.1%)

# of inodes with ind/dind/tind blocks: 311/15/0

28839 blocks used (80%)

0 bad blocks

0 large files

838 regular files

60 directories

0 character device files

0 block device files

0 fifos

14 links

160 symbolic links (160 fast symbolic links)

0 sockets

--------

1072 files

FILESYSTEM CLEAN

Remounting the root filesystem read-write...

kernel.sem = 1900 32000 32 128

vm.overcommit_memory = 1

Welcome to Cisco Service Engine

Sun Jan 1 00:00:00 UTC 2006

********** rc.aesop ****************

rsrc_file:/etc/aim_rsrc_file

Populating resource values from /etc/aim_rsrc_file

rsrc_file:/etc/default_rsrc_file

Populating resource values from /etc/default_rsrc_file

==> Platform aim, management interface is eth0

IOS IP Address Registration complete.

Kernel IP routing table

Destination Gateway Genmask Flags MSS Window irtt Iface

192.168.1.0 * 255.255.255.0 U 0 0 0 eth0

default 192.168.1.5 0.0.0.0 UG 0 0 0 eth0

Size of buff is: 65536

65536 bytes written

Reading License... Parsing...

12 MAILBOX LICENSE

/tmp/license/voicemail_lic.sig

done

Reading Limits...

Processing: /lib/python2.3/startup/limits.xml

Processing: /bin/products/cue/limits.xml

done

INIT: Entering runlevel: 2

********** rc.post_install ****************

Changing owners and file permissions.

Change owners and permissions complete.

INIT: Switching to runlevel: 4

INIT: Sending processes the TERM signal

STARTED: dwnldr_startup.sh

Welcome to Cisco Systems Service Engine Helper Software

Please select from the following

1 Install software

2 Reload module

3 Disk cleanup

(Type '?' at any time for help)

Choice: 1

Package name: cue-vm-k9.nm-aim.3.2.5.pkg

Server url: ftp://192.168.1.2/

Username: cisco

Password:

Downloading ftp cue-vm-k9.nm-aim.3.2.5.pkg

Bytes downloaded : 182040

Validating package signature ... done

- Parsing package manifest files... complete.

No installed manifests found.

- Checking Package dependencies... complete.

Downloading ftp cue-vm-langpack.nm-aim.3.2.5.pkg

Bytes downloaded : 1000665

Validating package signature ... done

Found Add-On Subsystem SID: e2e81cc6-39b5-47e1-9f83-b83c897fc50c Name: CUE Voicemail Language Support Version: 3.2.3.0

Found Add-On Subsystem SID: c28339fa-f7ae-4732-85ab-fa6c68b5de0c Name: CUE Voicemail Italian Version: 3.2.3.0

Found Add-On Subsystem SID: 49f09114-e0b0-4721-8b85-04be2064920c Name: CUE Voicemail European Spanish Version: 3.2.3.0

Found Add-On Subsystem SID: 27e5e2ab-1622-4c02-8a0a-cfad0d932148 Name: CUE Voicemail US English Version: 3.2.3.0

Found Add-On Subsystem SID: cf860289-67ac-4886-9295-a41e4c7a8487 Name: CUE Voicemail European French Version: 3.2.3.0

Found Add-On Subsystem SID: f0a41398-3917-4d49-b5ab-c2b39a80c121 Name: CUE Voicemail Latin American Spanish Version: 3.2.3.0

Found Add-On Subsystem SID: c4ca62e2-daff-40dc-b94e-bf20094bd700 Name: CUE Voicemail Mexican Spanish Version: 3.2.3.0

Found Add-On Subsystem SID: 88a84158-c090-4203-bde8-0d62eda200c7 Name: CUE Voicemail Arabic Version: 3.2.3.0

Found Add-On Subsystem SID: ab049397-cfad-4952-852a-8dfa69780cb8 Name: CUE Voicemail Dutch Version: 3.2.3.0

Found Add-On Subsystem SID: d60c3add-0c6b-4a99-8e5c-31019fe7939e Name: CUE Voicemail Swedish Version: 3.2.3.0

Found Add-On Subsystem SID: 683674a5-e6ef-4c97-8e05-efbba1e6fe47 Name: CUE Voicemail Canadian French Version: 3.2.3.0

Found Add-On Subsystem SID: b18bcd35-5a37-46af-b230-0d9c27713dec Name: CUE Voicemail Turkish Version: 3.2.3.0

Found Add-On Subsystem SID: fa803d25-9c89-4171-a14c-ec12d6ed6b8c Name: CUE Voicemail UK English Version: 3.2.3.0

Found Add-On Subsystem SID: 3f968fd0-6598-48e2-be1c-4af6c2e02e02 Name: CUE Voicemail German Version: 3.2.3.0

Found Add-On Subsystem SID: 88f73a6c-884d-4838-b162-1b544dd6583f Name: CUE Voicemail Danish Version: 3.2.3.0

Found Add-On Subsystem SID: a2ba4f96-3452-40c3-83ad-c442cb6bf42f Name: CUE Voicemail Brazilian Portuguese Version: 3.2.3.0

Found Add-On Subsystem SID: ea206a88-e44f-488b-a660-114a3b179065 Name: CUE Voicemail Korean Version: 3.2.3.0

Found Add-On Subsystem SID: 372fa3fd-1efb-4353-9005-45876646a351 Name: CUE Voicemail Mandarin Chinese Version: 3.2.3.0

Found Add-On Subsystem SID: 6cdfed34-6d45-48fd-afe0-717e589c9aa9 Name: CUE Voicemail Japanese Version: 3.2.3.0

Found Add-On Subsystem SID: 24cb0b00-ed1c-4463-bf6f-261b15dfb3e7 Name: CUE Voicemail Russian Version: 3.2.3.0

- Parsing package manifest files... complete.

- Checking Package dependencies... complete.

- Checking Manifest dependencies for subsystems in the install candidate list...

complete

WARNING:: Software installation will clear disk contents

Continue [n]? y

cleaning fs

prepfs.sh: aim reiser /mnt clean

hd_name: /dev/hda

hd_part: /dev/hda1

umount: /dev/hda1: not mounted

check_partition_count: 0

check_partition_flag: 1

Command (m for help): Partition number (1-4):

Command (m for help): Selected partition 1

Command (m for help): Command action

e extended

p primary partition (1-4)

Partition number (1-4): First cylinder (1-993, default 1): Using default value 1

Last cylinder or +size or +sizeM or +sizeK (1-993, default 993):

Command (m for help): Command action

e extended

p primary partition (1-4)

Partition number (1-4): First cylinder (6-993, default 6): Using default value 6

Last cylinder or +size or +sizeM or +sizeK (6-993, default 993): Using default value 993

Command (m for help): The partition table has been altered!

Calling ioctl() to re-read partition table.

Syncing disks.

mkreiserfs 3.6.19 (2003 www.namesys.com)

Starting payload download

File : cue-vm-full-k9.nm-aim.3.2.5.prt1 Bytes : 13448616kernel BUG at buffer.c:539!

invalid operand: 0000

cisco_rbcp

CPU: 0

EIP: 0010:[<c01311b5>] Tainted: PF

EFLAGS: 00010282

EIP is at __insert_into_lru_list+0x1d/0x68 [kernel]

eax: 00000000 ebx: 00000002 ecx: c819c140 edx: c03047d4

esi: c819c140 edi: cc3ca980 ebp: cd523e38 esp: cd523e34

ds: 0018 es: 0018 ss: 0018

Process dwnldr (pid: 487, stackpage=cd523000)

Stack: 00000002 cd523e50 c0131ad0 c819c140 00000002 c819c140 00001000 cd523e5c

c0131ae8 c819c140 cd523e68 c0133ed1 c819c140 cd523e8c c01835d6 cd523ed0

cc3ca980 00001000 00000000 c819c140 00001000 00000000 cd523ef0 c01836ee

Call Trace:

[<c0131ad0>] __refile_buffer+0x54/0x60 [kernel]

[<c0131ae8>] refile_buffer+0xc/0x10 [kernel]

[<c0133ed1>] __mark_dirty+0x19/0x20 [kernel]

[<c01835d6>] __commit_write+0xea/0x154 [kernel]

[<c01836ee>] reiserfs_commit_write+0xae/0x1b0 [kernel]

[<c0183640>] reiserfs_commit_write+0x0/0x1b0 [kernel]

[<c0170018>] nfs_writepage_async+0x5c/0xdc [kernel]

[<c0125e79>] do_generic_file_write+0x279/0x39c [kernel]

[<c0126249>] generic_file_write+0xf1/0x10c [kernel]

[<c0184211>] reiserfs_file_write+0x21/0x60 [kernel]

[<c012ff68>] sys_write+0x94/0xf0 [kernel]

[<c0108b13>] system_call+0x33/0x40 [kernel]

Code: 0f 0b 1b 02 9f 69 23 c0 83 3a 00 75 05 89 0a 89 49 24 8b 02

<0>Rebooting in 2 seconds...

Initializing memory. Please wait. ...

*Jul 13 23:07:41.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration:

*Jul 13 23:08:01.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to upFound disk 0

found 1 drives

root cmd : root (hd0,0)

Filesystem type is reiserfs, partition type 0x83

kf: a1 : /bzImage root=/dev/hda1 ro plat=aim

kf: a2 : /bzImage root=/dev/hda1 ro plat=aim

in grub_open: /bzImage root=/dev/hda1 ro plat=aim

in grub_open1: /bzImage root=/dev/hda1 ro plat=aim

in grub_open2: /bzImage root=/dev/hda1 ro plat=aim

in grub_open3: /bzImage root=/dev/hda1 ro plat=aim 1

in grub_open4: /bzImage root=/dev/hda1 ro plat=aim

kernel_func: kt: 0

Unable to load image

in boot func: kt: 0

Unable to boot image

Initializing memory. Please wait. ... 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...

*Jul 13 23:08:21.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down[BOOT-ASM]

Please enter '***' to change boot configuration:

*Jul 13 23:08:31.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to upFound disk 0

found 1 drives

root cmd : root (hd0,0)

Filesystem type is reiserfs, partition type 0x83

kf: a1 : /bzImage root=/dev/hda1 ro plat=aim

kf: a2 : /bzImage root=/dev/hda1 ro plat=aim

in grub_open: /bzImage root=/dev/hda1 ro plat=aim

in grub_open1: /bzImage root=/dev/hda1 ro plat=aim

in grub_open2: /bzImage root=/dev/hda1 ro plat=aim

in grub_open3: /bzImage root=/dev/hda1 ro plat=aim 1

in grub_open4: /bzImage root=/dev/hda1 ro plat=aim

kernel_func: kt: 0

Unable to load image

in boot func: kt: 0

Unable to boot image

Initializing memory. Please wait. ...

*Jul 13 23:08:51.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1, changed state to down 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

So you can see both TFTP and FTP works properly, normally after:

WARNING:: Software installation will clear disk contents

Continue [n]? y

Next step you should see the screen to choose the language, and continue.

But for mine, it didn’t shows me the choose language screen, however it went rebooting again, and then the rebooting just cycling as previous.

Anyone has encountered the same problem before? Or some experience guy can give me a help.

Thanks a lot.

Cooltree

cooltreedan · ‎07-13-2013

please everybody, thanks ahead!

paolo bevilacqua · ‎07-14-2013

You should use latest CUE software, not that old one.

cooltreedan · ‎07-15-2013

Hi Paolo,

actaully I tried, but the same result, so that's why I choose the the old version to near the previouse version in the CUE, I believe is 2.x.x. Any other idea?

thanks,

paolo bevilacqua · ‎07-15-2013

Can be faulty hardware.

cooltreedan · ‎07-16-2013

Don't know at this moment. I bought it on ebay, so before I ship it out, hope I can fix it.

thanks,