05-12-2021 07:09 AM - edited 05-12-2021 07:11 AM
Hi,
my presence/IM server shows wrong current UTC Time. (20:42 instead of 15:42)
NTP is enabled and Publisher has correct UTC Time and timezone set.
I did the following workaround: I set a "wrong" timezone (Etc/GMT+5) on the presence server.
Now at least the current time in my timezone is correct.
Any advice how to correct the current UTC Time?
Thanks in advance
Solved! Go to Solution.
05-17-2021 08:49 AM
As @Jaime Valencia mentioned, pub Is not synced try restarting your ntp.
is this a a Windows based NTP ? if yes Windows NTP server is not supported for CUCM; however, other types such as Linux NTP sources, Cisco IOS NTP sources, and Nexus OS NTP sources are acceptable.(This is from a one year old Cisco document. not sure if there was any update regarding the windows)
05-12-2021 07:28 AM
Does the CUCM publisher has the right time? UTC and whatever timezone you configured?
05-12-2021 08:30 AM
Yes the publisher has the correct time for UTC time in my correct time zone "Europe/Zurich"
05-12-2021 08:54 AM
Does the ntp status show correctly with your PUB?
What NTP stratum are you using?
05-17-2021 08:19 AM
Here the output from ntp status from publisher.
stratum is 2
05-17-2021 08:32 AM
It's also UNsynchronized, start by restarting the NTP or switch to another NTP.
05-13-2021 07:06 PM
CUCM publisher, Is it synced with the NTP ? Can you share output of utils ntp status from pub ?
05-17-2021 08:15 AM - edited 05-17-2021 08:16 AM
Hi, here the output from utils ntp status from pub
05-17-2021 08:49 AM
As @Jaime Valencia mentioned, pub Is not synced try restarting your ntp.
is this a a Windows based NTP ? if yes Windows NTP server is not supported for CUCM; however, other types such as Linux NTP sources, Cisco IOS NTP sources, and Nexus OS NTP sources are acceptable.(This is from a one year old Cisco document. not sure if there was any update regarding the windows)
05-13-2021 07:11 AM
Hi,
Is your IM&P is reachable with your NTP and DB replication is fine ?
Cisco highly recommends the use of a Stratum 1, Stratum 2, or Stratum 3 NTP server as the CUCM Publisher's external NTP reference. Any NTP source for the CUCM publisher MUST NOT be higher than stratum 4.
The external NTP servers defined for the CUCM Publisher node MUST be NTP v4 to avoid potential compatibility, accuracy, and network jitter problems. NTP version 4 is backward compatible with version 3; however, many issues were observed with attemps to use different NTP versions.
Pls rate if its Helpful. If this answered your question pls click Accept As Solution.
05-18-2021 01:07 AM - edited 05-18-2021 01:13 AM
Thanks Guys, Problem solved!
All your inputs were very helpful.
The old configured ntp server was my Windows Domain controller, which is not supported and I did not know that.
I switched to Google NTP server and ntp status is synchronized and shows correct UTC and local time!
Google NTP Server:
FQDN: time1.google.com.ntp
IP addresses: 216.239.35.0
Appreciate your help, Thanks guys!!
05-18-2021 01:08 AM - edited 05-18-2021 01:10 AM
05-18-2021 10:26 PM
@cataldo.fornito As it was @Nithin Eluvathingal reply that mentioned that NTP on Windows servers is not supported IMO I think that out of courtesy you should mark his response as the answer to your post, not your own reply.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide