Using CIMC, I've mounted an ISO image, for re-imaging of an APIC server. The CIMC, and NFS-server is connected to the same switch on the same LAN.. Both 1G. Server boots from the KVM-mounted ISO, but performance is non-existing. Is this a no...
Forum Posts
Resolved! UCS API using Redfish to change Timezone
Hi together I try to configure the UCS timezone via the Redfish API, the only thing that I found so fare was: Changing "DateTimeLocalOffset", this works so far to change the utc / localtime. but not the correct timezone. Did anybody manage to set th...
Hi Everyone, I would like to know if east-west traffic on same UCS domain but blade servers on different Chassis traverse north bound to uplink switches? Currently I have a setup where host vnics on vmware vcenter are set to active-active. Intersight...
hello everybody i hope anyone could help me. So we pulled blade out from one chassis, put it in in another one. Blade has discovered well, but the problem is it has onle connect to A IO module. 2 backplane ports on A`s backplane are accossiated with...
We have a UCS C240 M4SX that is out of coverage now (no contract) though the plan is to replace this with a new server, but for now we're stuck with it. The problem is, virtual disk 0 is down because we have 2 disks (1 and 2) that were in a predicted...
Does any has been able to install Windows server 2012 On a B200 M3 blade running 2204XP As fex with VIC 1240 card installed in blade. I am running 2.0(4b) On B 200 M 3 blades & while trying to install Windows 2012 . It installed succesfully since i a...
Hi, I have a project in which I am upgrading 3 Cisco C220 M4S's to ESXi 6.7 (PID: UCS-SP-C220M4-A1). One of the hosts seems to have a bad FlexFlash controller in it. I've not worked on M4's much, but in my research, it's been suggested in at least ...
Hello Bro, Recently I was making changes to Cisco UCS server B200-M4, I have changed the management IP "IP pool, and Fabric IPs'".Everything went Ok, and ended up with error log "Service profile SP-Blade2 configuration failed due to power-...
Good morning. We're trying to reset this device from scratch by removing the existing VMware EXSI we deployed recently. Until recently, the GUI froze all of a sudden; as a result, we rebooted the server. While it was rebooting, VMware EXSI reached a ...
Resolved! Changing IP pools for Cisco ucs 5108
Hello Bros'I have a question regarding Cisco UCS system with specs as mentioned below:UCS manager 3.1(3b)Chassis 5108Ucs FI 6248upIO module 2208xpDue to creticality I wanted to consult you regarding changing the IP addressing used in the management a...
Trying to upgrade a UCSC-C240-M5SN firmware from 4.2 to 4.3. I am using a vKVM mounting the ISO, have done over 4 others without issue, this one will mount the ISO, reboot let me choose it as a boot option, load the drivers, then right before it shou...
I have Cisco UCS 5108 and trying to install Cisco UCS 6324 Fabric Interconnect for the configuration purposes. I can't boot it normally. it's give ma message of non-supported.
I'm absolutely new to UCS and I've inherited a system that is discontinued and out of support. I've been tasked with moving 40TB of data off this UCS/vSphere system and onto a newer system supported by our server team. (Server team is unfamiliar with...
Hi There I'm looking for a UCS Spec for Cisco Molding Labs 2.7 for 60 students to work simultaneously. looked for days but could not find the spec for my requirement. Any help is apricated Thank you
upon receiving power, it does in standby for a bit, before the blade health LED flashes green, and then the power button turns green, and it says that it is testing memory, before going back to standby, with a solid amber blade health LED. The RAM is...
