Hello fellow Sysadmins.A C220 M4 with the latest recommended firmware displays the following fault messages on latest version diagnostics at Server Health:PSU1 PSU1_PWRGD: Power Supply sensor for PSU1, State AssertedPSU2 PSU2_PWRGD: Power Supply sens...
Forum Posts
Resolved! Chassis /FEX Discovery policy - Error
I have noticed the following error in my UCSM environment: Chassis discovery policy conflict: Link IOM 3/1/1 to peer port A:N/A/1/76 not configured IOM 3/1/1 is the following: Type: FEXName: FEX3Model: Cisco Nexus 2232PP Fabric Ports: 1/1, sys/fex-3/...
I am not real knowledgeable of Cisco Servers. I was handed a new server to setup and I am a little confused. It does not have any drives in the front and one 600GB drive plugged into the back. Opening up the server shows that it is a PCIe slot. I hon...
Hi, I use a Cisco UCS 240 Server. Recently I installed 4 additional modules of 32GB RAM along with the existing 4 modules of 32 GB RAMs. I installed them on A1, B1, C1, D1 and G1, H1, J1, K1, but the one on B1 is not being detected. Any ideas why?
I am currently using only one FI as a single. Three chassis are connected, of which only one has four cables. Chassis No. 2 and No. 3 have two cables.It also uses external SAN storage over a FI-SAN switch-to-storage connection.ESXi on the server in c...
When upgrading from HX 3.0 to 3.5, the board firmware on the node was not upgraded in the middle, so the board firmware was manually upgraded. Next comes the phrase below. I need your help. Checking ESX Host Version on Cluster Nodes with NVMe Disks...
Customer has purchased genuine Cisco memory DIMMs to upgrade the Cisco UCS servers and would like to check if customer can install the memory DIMMs without voiding the Warranty and support entitlement
I have a C240 and was not powering on. I cleared the CMOS by jumpping header ping J38 Pin9-10The server powered up, fans started running, and power switch changed from yellow to green. Now I cannot access the console from the rear VGA port. What else...
Hello,I've a C480M5( 4.2.2a) server with VIC1455 having all 4 ports connected to N9K switches with LACP running RHEL8. On OS side, a bond is created using 4x vNICs mapped to 4 uplinks ports. In a recent test of a port shutdown on the switch, I could...
We are looking to repurpose a couple of Hyperflex machines(HXAF 220C M5SX) as standalone ESXi hosts. Since we are having a Cisco 12G Modular SAS HBA (MRAID) controller, we are planning to configure the pass-through option for the disks. I am not fi...
Hello,I was handed a Cisco C240 M6 LFF to install ESXi on . The issue is it does not have any hard drives in the front of the unit. There is only a 600GB drive plugged into the rear of the unit similar to this:from what i have found out this drive is...
Hello,I want to renew smartnet of our cisco UCSC-C240-M4S2, anyone know how to get the serial number if we not on front of the server?
I'm unable to SSH into the Fabric Interconnect Cluster IP and also each Fabric Interconnect A & B. Have tried with telnet FI cluster IP, FI-A and FI-B to port 22 all passed. Can browse to UCSM website as well. From UCSM, under communications manageme...
Hello all, i am not able to login FI with CLI & GUI using virtual and individual ip and also i can't able to ping FI virtual ip. the error while login via CLI is software error.IF anyone have solution kindly provide.
HiI have a C220 M4 server that needs upgrade.So I downloaded the lates HUU Iso.But it does not boot because of UEFI Secure BootSo I tried to turn off Secure boot only to find out it is not possible do turn offSo I mounted the ISO on my Windows 10 com...
