Hi,We recently have bought a UCS C220 M3 Server, in order to install a virtual environment through ESXi. When trying to install EXSi 4.1; the hard disks are not recognized and listed.When connecting to the Web GUI (CIMC), in the inventory, the disks ...
Labels
-
Buying Recommendation
(18) -
Call Control
(1) -
Cisco ACI
(2) -
Cisco Bugs
(2) -
Cisco Cafe
(5) -
Cisco Intersight
(1) -
Cisco Software
(1) -
Cisco.com Idea Center
(1) -
Collaboration Endpoints
(1) -
Collaboration Solutions
(2) -
Community Feedback Forum
(6) -
Community Ideas
(5) -
Conferencing
(1) -
CSC Content with No Valid Community to Post
(1) -
CUCM
(1) -
Data Center
(2) -
Data Center Networking
(1) -
HyperFlex
(142) -
Identity Services Engine (ISE)
(2) -
ISR 4000 Series
(1) -
LAN
(1) -
LAN Switching
(3) -
Network Management
(2) -
Online Chat Support
(1) -
Other
(1) -
Other Collaboration Applications
(7) -
Other Collaboration Topics
(4) -
Other IP Telephony
(2) -
Other Networking
(1) -
Other Switches
(2) -
Other Switching
(4) -
Other Unified Communications
(12) -
Other Unified Computing System
(700) -
Routing
(1) -
Server Networking
(1) -
Small Business Network and Smart Storage
(1) -
Small Business Routers
(1) -
Small Business Support Service
(1) -
Storage Networking
(1) -
Switching
(1) -
UC Applications
(8) -
UC Migration
(1) -
UCS Advantage Series
(9) -
UCS Central
(63) -
UCS Director
(19) -
UCS Manager
(396) -
UCS Networking and Storage
(193) -
UCS PowerTool
(48) -
UCS Solutions
(155) -
Unified Communications
(16) -
Unified Computing
(2) -
Unified Computing System (UCS)
(6,576) -
VDI
(3) -
Voice Gateways
(1) -
Wireless LAN Controller
(1)
- « Previous « Previous
- Next » Next »
Forum Posts
Resolved! B200 M3 only shows 1 FlexFlash Card
I have a B200 M3 blade running 2.2(1c) firmware. I have a 16G SD card installed in both slots.If I navigate to the equipment tab, expand my chassis and select the server then choose inventory and select storage, FlexFlash Controller 1 says my Physic...
I have a Two VIC Card on Blade B200 the driver version is 2.3 need HyperV-2012 Vfabricit gives me unsupported driver.
Hi UCS Community, hope I'm posting in the right place...I'm playing with Cisco UCS PowerTool cmdlets but having a hard time finding which one will get / list the VLANs configured for a particular vNIC. These are easy to find in UCS Manager (see scre...
B200M3 blade with Windows 2012R2 installed does not boot OS after firmware upgrade to 2.2(2c). UCSM shows no HW errors. Upgrade install passed smoothly.Try to power cycle, recover CMOS, but nothing changes. It boot in BIOS, no messages in console.
Before we have our network engineers reconfigure their infrastructure to allow network discovery from SCOM, does anyone know whether or not SCOM will include the virtual switches (Hyper-V or VMware), the UCS fabric interconnects, and the hosted virtu...
Hi all hope you can shed some light.I understood that the FI's switch east west traffic, Had an issue tonight where we removed Unplugged the north south portchannels to the layer3 network to upgrade the core and all VM's in the UCS lost connectivity ...
Enviroment: 2 x FI6296; 2 x 5108 with 6 B200M3 each. All servers have 2 x 300 GB SAS local drive, RAID 1.After upgrade to 2.2 one of servers indicates that local disks are missing (both of them). Invertory shows 0 disks in server. Two faults messages...
Is there any information about VM-FEX support for Windows Server 2012 R2 Hyper-V? In the middle of migration to 2012 R2 project and cannot go further without this.
I have had two recent cases of Flex Flash controller hanging up on two different C240 M3 servers. Luckily I have been able to resolve this issue by going into CIMC and resetting Flex Flash controller, but this is issue getting too frequent. We are us...
Hello,Does anyone know if the SCOM 2012 UCS pack can be used to monitor Cisco C-series server at the hardware level?If so, can it do this directly without going through UCSM (FICs)?If not, is there any sort of pack setup for monitoring of C-series se...
Hello,we have Central 1.1.(2a) running with a local database and we think about migrating that local postgres-db to an external db.Has anybody of you done that already?Or does anybody know, where to find a best-practive-guide?Thanks, Patrick
Resolved! Licensing UCS Central 1.1(1a)
Having an issue getting UCS Central licensed for the 5 initial domains. Following documentation; I go out to license portal but there is no field for a GUID.I've clicked on just about every link with in the portal but have found nowhere to enter the...
Hello,I am running ESXI 5.1.0 build 1065491 and I keep receiving the error below the only way to get the server back is by rebooting it.Lost access to volume52fa9798-2f07f05f-c1f7-b0faeb97d646(datastore1) due to connectivity issues. Recoveryattempt i...
Hi Guys,Is it possible to upgrade the infrastructure firmware only to the latest 2.2 version and leave the blades on 2.0 or 1.3 firmware.Reason is its hard to get downtime to reboot blade and some new blades with V2 CPU requires new firmware. Jibby
