About sanjaydev

sanjaydev · ‎03-30-2019

Thanks for your reply. VG310-->SIP-->CUCM-->SME-->ITSP We have 10 sites having the same config, only this site, in particular, has a problem. Sending test fax to HP number works great but no to other numbers. During some restrictions, I am unable to post configs here. But I tried taking voice class codec (though it has only 711 now) and tried enforcing 711 directly on the dial peer. When doing this it gets user busy error ( the destination is available). Does ANI make any changes in this routing because I tried setting up a station number in port and nothing helped? Please advise.

sanjaydev · ‎03-30-2019

Hello, We are trying to send a fax from VG-310 --> CUCM-->ISP we are getting Bearer Capability Not Implemented (65) and user getting a busy signal. So, I took G729 off and tried only with G711 and now it is User Busy(17) The SDP in the invite has annexb=no but when I receive back it doesn't have line itself. I assume the service provider accepts and require us to enable that? Codec preference in dial peer to set 711 and then 729 now. 729 matches. But 729 is not a preferred codec for a fax for its compression rate. How do I fix this? Thanks Sanjay

sanjaydev · ‎07-04-2018

Hello, Could someone help please... There is no incoming cal alert like ANSWER, IGNORE on Cisco 8851. Running with 12.X SIP firmware and 10.5 CUCM. How to enable this back or change the settings. Thanks.

sanjaydev · ‎06-07-2018

Could you attach the whole script please. .

sanjaydev · ‎06-07-2018

Thanks. Could you modify the script for me to ask for a site ID and PIN atleast for two sites. rest I can copy for them. Could you do that for me please? Thanks.

sanjaydev · ‎05-27-2018

Hello Forum, I have a setup like 5 locations. Each have different phone numbers and different script running in UCCX 11.5. We have asked to create an emergency script such that each call in all those 5 scripts will check for emergency. So I have created a emergency script with say, option 1 for enabling and 2 for disabling and prior to that it will let now the current status. But I wanted to know how can I enable authentication for those 5 sites. Each one should have different password and the script should ask for a PIN/Password prior to know the status of the emergency currently. I at least wanted to know how can I setup just a password for all those 5 in a single script. Currently for testing I have this password as parameter and put that in a script. It works. Your help is appreciated. Thanks. Sanjay

sanjaydev · ‎12-24-2017

Thanks. I checked that. ILS is in place but i am not seeing the data replicated for those. Do you know how to change SRV record to point to that cluster apart from doing in the DNS server, like local dns in the system or something like that. Or could you please suggest me how to register this to a different cluster. When I try to login having everything moved to that cluster it says the same error. Should I have to wait for the LDAP sync or ? Regards Sanjay.

sanjaydev · ‎12-24-2017

Hello Friends I have two clusters and I am able to login to one without issues. When I do the same config in a different cluster its says cannot communicate to the server. What should be checked on my client or the server to make this work? Regards Sanjay.

sanjaydev · ‎12-24-2017

Thank You Everyone.

sanjaydev · ‎12-18-2017

Thank you for the reply. What I wanted to know is what if I won't upload any of those certs and what type of impact will be there. Say I am getting an alert for ipsec.der certificate gonna expire. What should I do here since it is a self signed certificate. Just regenerate it or request csr and go through the process?

sanjaydev · ‎12-18-2017

So what happens if we dont upload the trust one? What will be the impact.

sanjaydev · ‎12-17-2017

Hello Friends What is the difference between a normal certificate and a trust certificate? Say tomcat or ipsec with tomcat or ipsec trust certificates. I looked Cisco docs and could get far with it. Could someone explain more on this. Regards Sanjay

sanjaydev · ‎07-04-2017

Thanks everyone, So my question is to be a SIP phone. Either it is 7942 or 8851 or 997x... I wanted to understand in what scenarios does a IP phone send invite to CUCM. Does all SIP phones supports digit by digit and enbloc? I see an INVITE Like 9@xxxx when the dialed digits is 10 longer. Why is this behavior. Thanks Sanjay

sanjaydev · ‎07-04-2017

Hello, Please help me to understand the below. SIP ( Cisco 7942) phone registered to CUCM. When dialing out, do you think the phone sends out an INVITE to CUCM or the CUCM starts composing one and sends out. How does the digit analysis happens here. Thanks Sanjay.

sanjaydev · ‎04-03-2017

Jaime I read and couldn't find a place where it tells that this would be replaced by a AXL step or not needed anymore. Maybe i am not understanding... 1. Do you mean installing im&p server will automatically add as a sub to cucm or should we manually add it. 2 . Could you please let me know a doc where it exactly explains. Thanks Sanjay

sanjaydev · 03-30-2019

Thanks for your reply. VG310-->SIP-->CUCM-->SME-->ITSP We have 10 sites having the same config, only...

sanjaydev · 03-30-2019

Hello, We are trying to send a fax from VG-310 --> CUCM-->ISPwe are getting Bearer Capability Not Im...

sanjaydev · 07-04-2018

Hello, Could someone help please... There is no incoming cal alert like ANSWER, IGNORE on Cisco 8851...

sanjaydev · 06-07-2018

Could you attach the whole script please. .

sanjaydev · 06-07-2018

Thanks. Could you modify the script for me to ask for a site ID and PIN atleast for two sites. rest ...

sanjaydev · 05-27-2018

Hello Forum, I have a setup like 5 locations. Each have different phone numbers and different script...

sanjaydev · 12-24-2017

Thanks. I checked that. ILS is in place but i am not seeing the data replicated for those. Do you kn...

sanjaydev · 12-24-2017

Hello Friends I have two clusters and I am able to login to one without issues. When I do the same c...

sanjaydev · 12-24-2017

Thank You Everyone.

sanjaydev · 12-18-2017

Thank you for the reply. What I wanted to know is what if I won't upload any of those certs and what...

sanjaydev · 12-18-2017

So what happens if we dont upload the trust one? What will be the impact.

sanjaydev · 12-17-2017

Hello Friends What is the difference between a normal certificate and a trust certificate? Say tomca...

sanjaydev · 07-04-2017

Thanks everyone, So my question is to be a SIP phone. Either it is 7942 or 8851 or 997x... I wanted ...

sanjaydev · 07-04-2017

Hello, Please help me to understand the below. SIP ( Cisco 7942) phone registered to CUCM. When dial...

sanjaydev · 04-03-2017

Jaime I read and couldn't find a place where it tells that this would be replaced by a AXL step or n...

Date Registered	‎11-01-2015 10:44 PM
Date Last Visited	‎04-08-2019 03:16 PM
Total Messages Posted	86

Re: Bearer Capability Not Implemented (...

Bearer Capability Not Implemented (65) ...

Incoming call notification is not worki...

Re: UCCX Emergency Script 11.5 for vari...

Re: UCCX Emergency Script 11.5 for vari...

UCCX Emergency Script 11.5 for various ...

Re: I am unable to login to Cisco Jabbe...

I am unable to login to Cisco Jabber

Re: What is the difference between a no...

Re: What is the difference between a no...

Re: What is the difference between a no...

What is the difference between a normal...

Thanks everyone,

Will a Cisco SIP phone sends out INVITE...

Jaime

Re: Bearer Capability Not Implemented (65) - VG310

Bearer Capability Not Implemented (65) - VG310

Incoming call notification is not working in Cisco 8851

Re: UCCX Emergency Script 11.5 for various location in a single script?

Re: UCCX Emergency Script 11.5 for various location in a single script?

UCCX Emergency Script 11.5 for various location in a single script?

Re: I am unable to login to Cisco Jabber

I am unable to login to Cisco Jabber

Re: What is the difference between a normal certificate and a trust certificate?

Re: What is the difference between a normal certificate and a trust certificate?

Re: What is the difference between a normal certificate and a trust certificate?

What is the difference between a normal certificate and a trust certificate?

Thanks everyone,

Will a Cisco SIP phone sends out INVITE when dialing out?

Jaime