Hi,   I have a scenario with with vPC domains. I have double sided vpc confiuration. Client requirs routing between these 2 vPC domains.  Can I have HSRP configured on both vPC to take full advantage of the link speed.   I have attached the diagram for reference.   SWITCH A and B in vPC domain 100 SWITCH C and D in vPC domain 200     ... View more

Hi,   Is it possible to add the the ACI 9K switches to the PI(3.X) and APIC-EM(1.6)?   Faizal ... View more

Hi,   I would like to get some light on the below SAN output   SAN-SW-01# show fcdomain fcid persistent vsan 10 Total entries 1. Persistent FCIDs table contents: VSAN WWN FCID Mask Used Assignment Interface ---- ----------------------- -------- ------- ---- ---------- --------- 10 10:00:00:00:c9:75:00:d3 0xee0000 SINGLE NO DYNAMIC -- SAN-SW-01# show fcdomain fcid persistent vsan 10? <1-4093> VSAN id   What does the term dynamic means?  I have seen it can be made to Static. also. What difference it makes?   I have a deployment coming up. I am new to the SAN environment. Appreciate if some one can clarify this point.   Faizal      ... View more

Hi All, I am very much new to the ACI architecture . I have a new deployment coming up. I have attached the the diagram with physical connection. I would like to know whether this is a feasible thing in an ACI architecture. We are firewalling all traffic between the user segment and the servers.Firewall is not integrated with APIC.   Server VLAN's GW is the firewall interface. Currently all servers and vm will be configured as baremetal devices. The servers should be able to communicate with out the need of any contracts. May be in same EPG. All the servers should have redundant links to LEAF switches. But there is no VPC in place.We have restrictions in the VM end to create LACP.It will be done in future. Hope we have STP block loops.   The access-layer contains multiple vlans . All vlans are distributed over the access switches.Can ACI switch act switch traffic between these vlans(like inter-vlan routing)? Also I would like this network to go out to Firewall for access to server and internet...Can we have a default route to the Firewall interface? How should I segment this Servers and Access Layer part? using different Tenants or with Multiple VRF under a single tenant?   Appreciate your valuable suggestions and feedback ... View more

Hi ,   I have a site with CUCM 9.1 and using MGCP GW.   I have an extension 5234 with a prefix applied for Calling Party for the  outgoing calls like prefix 03112.   The Calling Party Selection is set as " First Redirect Number". "call forward all" is set to an external mobile number on the extension 5234.   When someone calls on the extension 5234 and call is being forwarded, I see only the extension number(5234) as calling party in the MGCP GW while doing the ISDN q931. Can any please suggest why this is happening?   But when a call is made from the extension 5234, the calling party number is displayed as 031125234.   Faizal   ... View more

Hi, The below is my scenario Phone A : 1001 Phone B : 1002. All Calls forwarded to Phone C which is 1003. I want the Phone C to display the Inbound Caller Id as 1001 when Phone A calls Phone B. Is this possible in CUCM . My CUCM version is 8.6 Appreciate your valuable suggestions... Faizal ... View more

Hi. I have scheduled an automatic back of the CCM v 6.0.1.3000-7. Back-up is scheduled for 16 th of every month. What I am seeing here is every month the number of file are getting reduced.There were about 10 files in the backup done in April.I have only 5 files in MAY and JUNE. Only new user creation and deletion happens on this system for the last few months. Is this an incremental backup? Any suggestions.. Mohamed Faizal ... View more