We have a bonded T1 frame-relay at our location. One of the circuits has gone down for an extended time and we were wondering if we can remove the frame-relay interface to get a single T1 connection working.   Plain and simple - is there a way to make half of the bonded T1 work on it's own? And, does a change on the router need to be made by the provider as well?   Here's the status of the interfaces:  Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL ------------------------------------------------------------------------ * FastEthernet0/0 0 0 0 0 1000 2 1000 2 0 FastEthernet0/1 0 0 0 0 0 0 0 0 0 * Serial0/0/0 0 0 0 0 0 0 0 0 0 Serial0/1/0 0 0 0 0 0 0 0 0 0 * MFR1 0 1 0 0 0 0 0 0 0 MFR1.500 - - - - - - - - -   Running partial config (cleaned for security): ! interface MFR1 description ISP MultiLink Frame Relay Bundle no ip address no ip redirects no ip unreachables no ip proxy-arp ip nbar protocol-discovery encapsulation frame-relay IETF ip route-cache flow load-interval 30 fair-queue no arp frame-relay frame-relay multilink bid to gw frame-relay lmi-type ansi hold-queue 300 out ! interface MFR1.500 point-to-point description IPS MultiLink Frame Relay PVC ip address 66.88.111.222 255.255.255.252 no ip redirects no ip unreachables no ip proxy-arp ip accounting output-packets ip nbar protocol-discovery no ip mroute-cache no cdp enable no arp frame-relay frame-relay interface-dlci 500 IETF ! interface FastEthernet0/0 description To FW ethernet ip address 66.88.222.241 255.255.255.240 ip nbar protocol-discovery ip route-cache flow duplex full speed auto no cdp enable ! interface FastEthernet0/1 no ip address ip nbar protocol-discovery shutdown duplex auto speed auto ! interface Serial0/0/0 description ISP Frame Relay T1 no ip address no ip redirects no ip unreachables no ip proxy-arp ip nbar protocol-discovery encapsulation frame-relay MFR1 no ip route-cache cef ip route-cache flow service-module t1 remote-alarm-enable no arp frame-relay ! interface Serial0/1/0 description ISP Frame Relay T1 no ip address no ip redirects no ip unreachables no ip proxy-arp ip nbar protocol-discovery encapsulation frame-relay MFR1 ip route-cache flow no arp frame-relay ! ip classless ip route 0.0.0.0 0.0.0.0 66.88.111.220 !   Thanks   ... View more

A user connecting with a Mac using the built in Cisco VPN for IPSec is having routing issues. The location the client is at has the same subnet as our company network they are trying to connect to; 192.168.1.0/24. The VPN client connects fine but routing can't tell the difference from the client's site and ours. Their Windows machine at the site using the old Cisco VPN client works fine.  Is there any software for Mac that will route traffic correctly? I already asked if they can change the network to 10.0.1.0/24 which they can't do. From the ASA config:  access-list Company_splitTunnelAcl extended permit ip object-group LocalVPNnet 192.168.0.0 255.255.255.0 ... View more

Hello,   We have a CUCM 7.1.3 system with a variety of Cisco VoIP phones (models 7910-12, 7960-61, 7965, and 8961's).   Is there a method to configuring paging to announce through all registered phones' speakers? If so, could someone point me in the right direction for documentation.   Thanks ... View more

We have multiple AIR-LAP1142N-A-K9 controlled by a AIR-WLC2106-K9. Is there a way to snmp query the individual radios for traffic stats? I can snmpwalk against the WLC but it only shows the physical ports of the controller, not the radios. Thanks ... View more

Our system is CUCM 7.1.3 with Unity 8.6. The 3911 SIP phone has a Messages button that when pressed does nothing. I can manually dial the voicemail box fine. In CUCM > Device > Device Settings > Phones Button Template > and select Standard 3911 SIP. There are only two buttons; 1 Line ** 2 None ** Load File     SIP3951.8-1-2SR1 APP Load ID     SIP3951.8-1-2-9 Boot Load ID     BOOT3951.0-0-0-9 DSP Load ID     DSP3951.0-0-0-2 Any thoughts on where to go with this? ... View more

CUCM 7.1.3 Hi, We have a series of phones that have registered and work as expected like 7912, 7940, and 7960's. However when I register and add a DN to a 3911 it can't place calls and doesn't have the typical dialtone sound. It can recieve calls to it however. It's a SIP phone running firmware SIP3951.8-1-2SR1. I saw some discussion on enabling 'Media Termination Point Required', but I don't see that in CUCM Admin > Media Resources > Media Termination Point or within the gateways. ... View more

Hi, We took our WS-3560G-24TS-S out of production after a few years of running without issue. I tried powering it up but there's no lights on the ports if we connect devices. The fan does kick in. The lights near 'Mode' go through a routine. There is also no info displayed over console. I tried powering it up while holding 'Mode' on the front and watching the console window with no POST info. I have opened up the chasis to see if there's anything more I can do to troubleshoot or 'reset' but it doesn't look like anythings there to mess with. Are there any other suggestions or things I can try? Thanks ... View more

Hello, We just received two Catalyst 3750X switches. Cisco's documentation provides cabling installs for StackPower in a three or more switch example. Can someone clarify the cabling of the two cables between two switches? Having two cables with green and yellow on either side and a switch with both colors signified beside it is a little confusing especially when considering electricity. Thanks ... View more