You question is not clear " can you complete question using what ?"   is this Model SG350 ? here is the admin guide you can do different VLAN go differend ADSL, can be PBR or directly segrate the VLANS to different Modems   https://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/350xg/admin_guide/AG_Tesla_350_550.pdf ... View more

here is best guides available :   https://docs.umbrella.com/deployment-umbrella/docs/3-deployment-guidelines   https://support.umbrella.com/hc/en-us/articles/235170467-Best-practices-for-Cisco-Umbrella-users ... View more

try below thread for SNMP ODI   https://community.cisco.com/t5/network-management/snmp-trap-mib-for-firepower/td-p/2948214 ... View more

here is smart Licensing :   https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9500/software/release/16-9/configuration_guide/sys_mgmt/b_169_sys_mgmt_9500_cg/configuring_smart_licensing.html ... View more

do you have config "same-security-traffic permit intra-interface"  ... View more

Can you post more information what error you getting, suggest to contact cisco License team over phone, they could able to fix quicker than community here.   ... View more

You can do with Policy based routing example guide -    https://www.cisco.com/c/en/us/td/docs/security/asa/asa94/config-guides/cli/general/asa-94-general-config/route-policy-based.html ... View more

Can you post show out put of below information :   show version show modules show process cpu history sorted show process cpu |  ex 0.00%   in related to your Issue, as mentioned by the post, when ever taking backup taking place you onbserved CPU high, what was the status when there is no backup ?   backup takeing from from where to where ? config backup or Databackup like DB backup so on ?   when you hitting the maximum load of the device, it is common to hit the CPU load high, but we need more information to confirm the same. ... View more

There is 2 options, if you have NMS in the organisation, you can used SNMP ODI and make Graphs another one you can use script to parse the information and store in Database and make your own reports     here is the URL for information to look for vpn connnection :   https://www.cisco.com/c/en/us/td/docs/security/firepower/630/fdm/fptd-fdm-config-guide-630/fptd-fdm-ravpn.html#concept_786C347B5D6845EB8026DF87BD45C7CB ... View more

here is the resource for you to setup  one you looking :   https://www.cisco.com/c/dam/en/us/products/collateral/switches/catalyst-9000/nb-06-cat-9k-stack-wp-cte-en.pdf   https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9500/software/release/16-9/configuration_guide/ha/b_169_ha_9500_cg/configuring_cisco_stackwise_virtual.html     ... View more

Guidelines and Limitations for High Availability Before initiating failover, you must consider the following prerequisites and limitations: You must have the hardware identical to the primary Prime Infrastructure to run a standby instance of Prime Infrastructure. Prime Infrastructure supports HA on both the physical and virtual appliance deployment models. A reliable high-speed wired network must exist between the primary Prime Infrastructure and its backup Prime Infrastructure. The primary and secondary Prime Infrastructure must be running the same Prime Infrastructure software release. The OVA file size in both primary and secondary Prime Infrastructure must be the same. Both primary and secondary Prime Infrastructure must be reachable on both sides. The health monitor process for the secondary Prime Infrastructure must be running during the HA registration. High reliable network must exist between the primary and secondary Prime Infrastructure. For primary Prime Infrastructure to initiate HA with a secondary Prime Infrastructure, the secondary Prime Infrastructure services must be running and reachable from the primary Prime Infrastructure. You must boot the secondary Prime Infrastructure first, and then boot the primary Prime Infrastructure to initiate HA registration. Failover should be considered temporary. The failed primary Prime Infrastructure should be restored to normal as soon as possible, and failback is initiated. The longer it takes to restore the failed primary Prime Infrastructure, the longer Prime Infrastructure runs without HA support. The latest controller software must be used. The primary and secondary host are not required to share the same subnet. They can be geographically separated. Any access control lists imposed between the primary and secondary Prime Infrastructure must allow traffic to go between the primary and secondary Prime Infrastructure. The primary Prime Infrastructure must have a sufficient number of licenses for the devices. When failover occurs, the secondary Prime Infrastructure uses the licenses of the primary Prime Infrastructure for the devices. A secondary Prime Infrastructure can only support one primary Prime Infrastructure. When HA is enabled for the first time, synchronizing the servers takes a considerable amount of time. The time it would take would be in the order of 30 minutes or more depending on the size of the database. During the HA registration, ensure that the bandwidth between the primary Prime Infrastructure and the secondary Prime Infrastructure is 1Gbps. If the bandwidth is too low, HA registration and failover will fail. Ensure that you remove HA from the Prime Infrastructure server before you being an upgrade to a newer version of Prime Infrastructure. ... View more

One suggestion if  the profile based on DNS FQDN, so put your New ASA DNS Entries as top priority, ... View more

I suggest for now to check the USB recognized, some USB may have issue, so check is the USB mounted on Cisco device.   ... View more

you are on switch: not on switch#   follow below thread to boot from USB, if not able to view USB follow next steps as per the thread :   https://community.cisco.com/t5/switching/catalyst-9200-ios-install/td-p/3926015 ... View more

Good Cisco guide to upgrade :   https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9200/software/release/16-9/configuration_guide/sys_mgmt/b_169_sys_mgmt_9200_cg/performing_setup_configuration.html ... View more