Hi Aman,   So to use PVDM3 DSP resources on the motherboard (slot 0), I would then need to have "dspfarm" command under voice-card 0 to enable DSP sharing: voice-card 0  dspfarm   Thanks. ... View more

Hi Aman,   I only have "show inv" with me.   NAME: "CISCO3945-CHASSIS", DESCR: "CISCO3945-CHASSIS" PID: CISCO3945-CHASSIS , VID: V02, SN: NAME: "Cisco Services Performance Engine 150 for Cisco 3900 ISR on Slot 0", DESCR: "Cisco Services Performance Engine 150 for Cisco 3900 ISR" PID: C3900-SPE150/K9 , VID: V06 , SN: NAME: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1" PID: VWIC3-2MFT-T1/E1 , VID: V01 , SN: NAME: "PVDM3 DSP DIMM with 256 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 256 Channels" PID: PVDM3-256 , VID: V01 , SN: NAME: "PVDM3 DSP DIMM with 256 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 256 Channels" PID: PVDM3-256 , VID: V01 , SN: NAME: "Network Module Adapter for SM Slot on Slot 1", DESCR: "Network Module Adapter for SM Slot" PID: SM-NM-ADPTR , VID: V01, SN: NAME: "High Density Voice2 Network module with on board two port interface on Slot 1", DESCR: "High Density Voice2 Network module with on board two port interface " PID: NM-HDV2-2T1/E1 , VID: V05 , SN: NAME: "3rd generation four port FXS DID voice interface daughtercard on Slot 1 SubSlot 0", DESCR: "3rd generation four port FXS DID voice interface daughtercard" PID: VIC3-4FXS/DID , VID: V03 , SN: NAME: "C3900 AC Power Supply 1", DESCR: "C3900 AC Power Supply 1" PID: PWR-3900-AC , VID: V04 , SN: NAME: "C3900 AC Power Supply 2", DESCR: "C3900 AC Power Supply 2" PID: PWR-3900-AC , VID: V04 , SN: ... View more

Hi Aaron,   Thank you for replying. By any chance do you know if the fxs ports should appear in the "show voice port summary" output? ... View more

Hi Aman,   Thanks for your kind reply, unfortunately the reply does not answer my question :)   1. I am not trying to install PVDM3 on the NM-HDV2 2. I am not installing PVDM2 on the C3945 router either   I would like to confirm if the VIC3-FXS/DID in NM-HDV2 is able to "leverage" the PVDM3 DSP resource on the motherboard (dsp sharing)   Thank you. ... View more

Question on the devices support (2,500 for high-density and 1,200 for m edium-density), is referring to devices Configured or Registered on CUCM? Example 1,300 devices configured but only 1,200 devices are registered? Thanks! ... View more

Hi Aaron, With UCCX 9.0(2), assume Silent Monitoring and Recording works for Jabber's agent as well? And, believe Jabber will be suitable deployment for remote agent (I.e home agent). Cheers! ... View more

Hi, Not sure if this is the right forum. But would like to clarify, for a redundancy BE 6000 setup with UCCX, is the HA Server Software License (example: L-CCX-90-A-PHA-LIC) a mandatory SKU? Cheers! ... View more