Hello,I am trying to establish a VPN connection between a SPA525g2 SIP phone and a RV180 router. When I attempt to make the connection the SPA525g2 give a "Failed to obtain WebVPN cookie" error. I understand that the 525g2 uses the Anyconnect VPN ...
I have two SPA525G phones. One works fine, the other is also connected to wifi but it doesn't have a ringtone. I want it to share the same phone number and ring when the first rings, etc, but I can't find how to configure that. Any clues?
I have been carrying out testing with Cisco SPA 504g.The device is connected to a third party SIP proxy, the proxy sends out an options request and the SPA returns 404 not found.I'm wondering if this is a security feature with SPA device or are optio...
The BE6000 Administration guide states that "Most BE6K deployments have a single domain as part of a Standard Prime installation. Multiple domains are available with Prime Collaboration Advanced (available for purchase) that can be used for complex B...
We have Cisco SPA525G and SPA525G2 running with Asterisk.When the phone is off the hook and another call comes in, it currently plays the Call Waiting beep through the handsets earpiece. How can we set this up so the phone actually rings rather than ...
I have two SPA302D handsets registered to an SPA232D base.My voip provider (voipfone.co.uk) provides a voicemail service.If a call is not answered, it is picked up by the voicemail system. A voicemail icon appears on the SPA302D with the number of m...
My UC320W has gone into a state which is not described in any of the troubleshooting guides. Symptoms are:The Power/Sys light flashes continuously, about twice a second.Power cycling has no effect.Resetting the UC320W appears to make no difference.L...
Hello,I'm testing music on hold with the 504g with firmware version 7.4.4When the music on hold server is set and hold is pressed INVITEs to the moh server are sent directly to the IP address returned on an A record lookup of the moh server. The pho...
We are running a UC500 and I see that after some time the avail mem reduces. After a reload, the avail memory sits at about 22%, but after a about 2 weeks it gets to about 12% avail. We have had a few unknown system restarts, and when looking at the ...
Hello,Does anyone know if it would be possible to configure a cisco phone based on an existing polycom configuration file?We have 12 spa509g phones that are barely working with our provider (voxox). VOXOX does not provide any support for cisco phones...
The problem is related to CISCO XML EXE Auth Mode option (tab 'Phone' section 'XML Service') on phone running firmware 7.5.5 in SIP mode.As long as option is changed via WWW UI only, everything work as expected. But if option changed using provisioni...
HI, ExpertI have a question about the condition when partner need to RMA. Does anybody have good solution for this.1, what if one of HDD HW fails, Need to RMA whole be6k Box? or can swap only failed HDD using a specific PID?2, what if the Fan fail...
Hi Guys, Recently one of the staff accidentally power down the UC540 and when she power it up again, the UC boot in factory default. So i tried to restore the previous config but it didn't work. It seems that the DHCP server is not working. The pho...
Hello Guys,I am having issues with wifi on the UC500 after I changes my switch SF300. my current config is as below. ot11Radio0/5/0 no ip address ! encryption vlan 1 mode ciphers aes-ccm ! ssid AGRI ! ssid cisco-voice ! speed basic-1.0 basic-2.0 basi...
We have several door boxes that simulate a POTS line to a phone system. Now that we have replaced our traditional PBX with an IP based system, we are using the SPA3102 to direct push buttons calls at a door box into the phone system. This works cor...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: