VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

We have a few sites where we have deployed 1700 routers behind the ISP's CPE. We have set up VPNs back to corporate. Has anyone found a way to use GRE/EIGRP/something to cause the router to dial when the primary goes down and re-establish the VPN? I...

wwwinc by Level 1
  • 347 Views
  • 1 replies
  • 0 Helpful votes

Hi there,Just wondering if it is possible to build a VPN tunnel from PIX to PIX withoutany data encryption. This will help increate performance on the boxes, althought I do not understand that it will not secure the data.Any help is greatly apprecia...

paulawong by Level 1
  • 826 Views
  • 2 replies
  • 0 Helpful votes

Hi,I have a Cisco SOHO 97 router and i have configure VPN to acess through VPN client.There is no problem : Client VPN connection --> OK, Access to my network --> OKIf i activate the IOS Firewall with CRWS: Client VPN connection --> OK, But I cannot ...

Can one configure the group on a VPN concentrator to have access to a certain subnet? The client will be using Cisco VPN client 3.6.1. Our tunnel endpoint is a VPN concentrator 3060. I would like to restrict a particular set of users to one certai...

dpatkins by Level 1
  • 370 Views
  • 1 replies
  • 0 Helpful votes

--begin ciscomoderator note-- The following post has been edited to remove potentially confidential information. Please refrain from posting confidential information on the site to reduce security risks to your network. -- end ciscomoderator note -- ...

jilahbg by Level 1
  • 516 Views
  • 3 replies
  • 0 Helpful votes

How does the username and password for the ISP dialup get configured such that the user doesn't need to input this? I'm assuming that this is in a .pcf file. When the client starts at logon and a dialup connection is selected the user is prompted f...

sweetser by Level 1
  • 449 Views
  • 4 replies
  • 0 Helpful votes

we are going to implement a VPN between two locations one at India and other at USA.we are going to use burstable T3 connection at US side and 2xE1 at India side.i wanted to use 2621 at both sides.but E1 Interface at the router is a V.35T3 Interface ...

Hi,I have an IPSec Tunnel between a PIX firewall and a Cisco 1721 router. Do i have any options regarding any routing protocol i can use ?Are there any plans to add GRE support to PIX, so that EIGRP, OSPF can be used ?\\ Naman

mnlatif by Level 3
  • 310 Views
  • 1 replies
  • 0 Helpful votes

I have installed vpn client in windows 2000 with local IOS authentication. First Problem is than subnet mask send from IOS not is correct, i use class A address with 24 bits subnet mask. I change this configuration in network connections (windows 200...

dicorel by Level 1
  • 569 Views
  • 1 replies
  • 0 Helpful votes

Hi,I believe vpn through nat is "enabled" in the 6.3.1 software for the pix? I am having problems getting it to work. Can anyone give me any pointers including anything I need to know about the router?I assume all I need to do is create a static 1 ...

agoodwin by Level 1
  • 454 Views
  • 3 replies
  • 0 Helpful votes

We have a PIX 515E running IOS 6.3 with 3 interfaces (inside, dmz & outside). The inside network is 192.168.1.0 / 24, and the DMZ is 172.16.1.0 /24. All VPN clients are assigned addresses in the range 192.168.10.1 to 192.168.10.254. Connecting via th...

mchard by Level 1
  • 725 Views
  • 6 replies
  • 0 Helpful votes