cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
396
Views
10
Helpful
5
Replies

1532E unable to join 9800 controller

JWHolm81891
Level 1
Level 1

So, I've been configuring new APs all week without a hitch, then there's this guy. A 1532E, this one is not out of the box but was previously on a 5500 controller we are phasing out. I wiped the AP back to factory settings knowing that APs can be sticky. I'm just not able to get this one to populate in the AP table so I can configure through the GUI. Here are the logs. Any thoughts?

 

*Jun 23 14:41:32.331: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 23 14:41:32.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:32.335: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:32.335: %CAPWAP-5-SENDJOIN: sending Join Request to 10.7.230.2
*Jun 23 14:41:32.339: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.7.230.2
*Jun 23 14:41:32.931: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 23 14:41:32.931: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 23 14:41:33.619: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jun 23 14:41:33.627: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jun 23 14:41:34.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jun 23 14:41:34.655: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 23 14:41:34.663: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jun 23 14:41:34.671: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jun 23 14:41:35.655: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jun 23 14:41:35.663: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 23 14:41:35.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 23 14:41:36.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 23 14:41:42.927: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 23 14:41:43.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:43.323: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:43.327: %CAPWAP-5-SENDJOIN: sending Join Request to 10.7.230.2
*Jun 23 14:41:43.327: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.7.230.2
*Jun 23 14:41:43.327: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.7.230.2:5246
*Jun 23 14:41:43.327: %CAPWAP-3-ERRORLOG: Go join a capwap controller

5 Replies 5

balaji.bandi
Hall of Fame
Hall of Fame

what is the WLC 9800 code running, have you checked the matrix it supported.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Nope.

Hi

  This AP 1532E does show on the compatibility matrix for IOS XE.

 

1532.JPG

 

 

 

Leo Laohoo
Hall of Fame
Hall of Fame

The other forum have already responded to this very same question:  1530 is not supported in the 9800.

jonathga94
Level 1
Level 1

The AP 1530 is not supported on the WLC 9800

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card