cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
13639
Views
15
Helpful
53
Replies

8.2MR5 Interim Availability

Javier Contreras
Cisco Employee
Cisco Employee

Release 8.2.145.x Interim (8.2MR5)

Final  code 8.2.151.0 is now posted, thanks for your interest!

New Updated version 8.2.145.64

This release adds the following functionality:

  • TKIP  support for 2800/3800/1800

8.2.145.64

CSCvc18129    Crash on RF profile/client exclusion sync on HA scenario

CSCvd19354  WLC crash while editing config rf-profile hsr-mode disable | enable config rf-profile 11b

CSCvd20843   Beacon stuck due to off-channel stuck

CSCvd25183   2800/3800 does not advertise the extension channel correctly when DCA assigns Bandwidth.

CSCvd29298  2800/3800 - Type 3 off-channel stuck due to callback missing during off-channel

CSCvd07243  Unable to change AP name nor location from the GUI

CSCvc87207  AP2800 802.11b/g radio dropping RTP packets

8.2.145.58

CSCvd16523        AP3800/2800: New CLI to make core dump extended not persistent across upgrade

CSCvc59252        1852 AP showing only power level 1 instead of power level 1 to 8 under 5 Ghz radio

CSCvd16939        1800 Band-Select does not work

CSCvd16993        2800/3800 - Rxhang Fixes

CSCvb94413        2800/3800 -  Fix DAA

CSCvd00405        Silent reboot observed for 3800

CSCvd07657        AP1810 fails to get ARP response intermittently leading to a full reboot

CSCvd18791        2800/3800 - NSS counters after next-hop-MAC failure in capwapd

CSCva91457        WLC: repeated crashes w/Reason: spamApTask4

CSCvc52619        Local EAP do not support any of ciphers, used by 8821 phone

CSCvb77682       2800/3800 -  ioctl error message when setting XOR to 5GHz band

CSCvb73104        AP 1600: Radio d1 reset: FW: irq/mac stat=40000/10000000 command timeout

CSCvd07215        1800/2800/3800 doesn't learn dhcp lease time from dhcp server and defaults to 24hr.

CSCvd09482        2800/3800 - Rxhang Fixes

CSCvd03656       AP2800/3800 not updating ndp to WLC due to Status: NSS_INVALID_PARAM

CSCvd05596        2800/3800 - Rxhang Fixes

8.2.141.40

CSCvb94799 mc2uc packet packet lost with AP 3802E
CSCvc89939 2800/3800: 40 mhz ext offset 8.2.145.33
CSCvc90559 2800/3800: RX Hang seen on alpha 8.2.145.36
CSCvc61560 WLC radius auth aaaQueueReader "Unable to fit Radius packet in allocated memory"
CSCvb78834 wlc crashing with task name emweb
CSCvc64343 AP1530 detected a lot of radars
CSCvc60233 2800/3800: Off-channel timeout is observed
CSCvc86514 2800/3800 - AP CAPWAP reset when extended Radio coredump is enabled
CSCvc81662 2800/3800: RX Hang seen on alpha 8.2.145.26
CSCvc71905 2800/3800: AP detects radar in the absence of radar sources (8.2.131.40)
CSCvc81491 2800/3800: high latency issues on on build 8.2.145.26
CSCvb94436 TKIP support for 1800 series APs
CSCvc52004 1800: iOS device connect to the dot1x network slowly
CSCvc70133 1800/2800/3800: AP flex: MC40 11g client sending Assoc req with g rates in extended rates display issue
CSCvc80161 2800/3800 11n/ac clients failing to associate with XOR in 5GHz
CSCvc11544 Default Neighbor Pruning Timer need to be increased to keep neighbor entries for 1 hour
CSCvc76148 2800/3800 Beacon drift causing mc9060 client drops

8.2.141.26

CSCur63031

AP error: %ENTROPY-0-ENTROPY_ERROR: Unable to collect sufficient entropy

CSCur68316

802AP-891 in flexconnect mode are losing vlan mapping after power cycle

CSCuw41092

AP not send traffic indication in beacon for power-save client after FT

CSCux48308

Broadcast delivery stops with key rotation 1552 rap,  819W 153.3JBB5 wgb

CSCux51833

Client fails on RAP with AAA Override ACL when AP is in Flex+Bridge Mode

CSCux78389

Radius Failover should failover both authacct server on WLAN

CSCux85357

WLC sends GARP for flex local switching clients after HA switch-over

CSCux88967

On MAC Filter failure  Client session timeout can not association back

CSCux95319

Roaming central to local auth causes in flex caused dot1x table failures

CSCux96500

WiSM2/WLC crash on bcastReceiveTask

CSCuy30583

5520 show imm chassis shows no results and crashes WLC

CSCuy53072

SNMP cLMobilityGroupMembersTable returns wrong  value from WLC in PI

CSCuy53596

CleanAir fatal error and radio reset on Flex+Bridge AP

CSCuy64520

Access Points (AP) sending CDP packets to the wireless clients

CSCuy71409

Client detailed params not synced to standby in fast ssid scenario.

CSCuy75241

5508 system crash with task mmMobility

CSCuy82849

Memory leak found@mm_heartbeat module on Guest anchor WLC

CSCuz05218

Barbados: show ap auto-rf   does not display  xor slot(0) neighbors

CSCuz11717

3-sec delay before sending "dot1x auth initiate" to SPAM with WSSI

CSCuz16883

Address registration issues for mobility scenarios

CSCuz18811

Flex: Local Switching WLAN is changing to Central Switching WLAN on add

CSCuz33818

profiler:  double free issue

CSCuz35221

Mobility handoff fails in new mobility dot1x CWA client reconnect

CSCuz40066

Guest Anchor:Foreign to Foreign roam fails on GA scenario

CSCuz40970

8510 anchor WLC Crash on task osapiBsnTimer

CSCuz49968

8.0 MR4 WLC crash during SNMP set opeartion

CSCuz50774

WLC lossing pings to itlsef Reaper cleaning up exited task osapi_ping_rx

CSCuz67292

Client not moving to RUN state after CAS perform posturing on client

CSCuz77747

Flexconnect: AP 1602 loses native vlan config on reload

CSCuz78555

Bulk sync status "In-progress" after standby boots up

CSCva01578

BARBADOS Ap not showing Syslog Server ip  with DHCP option-7

CSCva01762

AP1815/50: Over-ride Global credentials cleared on GUI after reboot

CSCva03376

UX-AP3702i After primed carrier set 5GHz only allowing four UNII3 ch

CSCva22440

3800: QBSS STA Count keeps incrementing with STA associating again

CSCva28211

AireOS UX AP : 'JP' should be used as world mode in Beacon/Probe Res

CSCva28524

WLC 8.3 - Creating SNMP community fails

CSCva31178

AP: 8.3 - Radio reset due to offchannel stuck

CSCva32411

Clients losing connectivity when reauth with DOT1X over 702w AP

CSCva48201

Unable to set static IP for AP from controller GUI

CSCva52825

2800/3800 does not do PMTU discovery during join/image download

CSCva63541

2/3800 AP CAPWAP restarts continuously during FTP transfer of large file

CSCva72724

AP2602 Crash "disc_tx_requeue_client" "dot11_get_rate_shift"

CSCva74487

8540 crash on running show commands task :emWeb

CSCva74927

Barbados Flex - AP disjoins with 'Failed to get ARP entry for WLC' error

CSCva83234

Barbados : Kernel Crash during image download

CSCva83884

WLC System crash on aaaQueueReader

CSCva87295

Flex AP radio reset during FT with Central dhcp and Nat-pat enabled

CSCva90343

Unable to do VLAN to RLAN mapping at FlexConnect Group

CSCva95251

DSCP traffic is not limited to maximum QoS Profile value

CSCvb09381

Unable to add or modify SNMP strings on a 5520 HA Pair running 8.1.122.0

CSCvb25233

Enable VLAN-RLAN Mapping in FlexConnect Group

CSCvb28231

Controller crashed due to memory corruption

CSCvb35173

Barbados: Radio crash  beacon stuck - due to lost txq reference

CSCvb43105

Barbados outer DSCP not same as inner with DSCP Trust upstream NSS

CSCvb44169

emWeb reaper reset after "clear mdns service-database all"

CSCvb44699

NMSP queue full due to Rouge AP task.

CSCvb48603

Evaluation of wlc for Openssl September 2016

CSCvb52310

Silent Boot on 2800/3800

CSCvb54166

Malformed 11v element on HSR WGB with WLC 8.2+

CSCvb66080

VLAN override from ISE is not working for RLAN with FlexConnect Local Switching

CSCvb69962

Client traps not showing session ID's

CSCvb71168

RSA256-AES256 dtls encryption lowers PMTU but AP doesnt' respect it

CSCvb72380

performance profile show all values as 0 after clear config for XOR radio

CSCvb79274

WGB wired client expiring periodically

CSCvb80511

CWA is not working for flex-bridge APs pointing ACL rx from Radius doesn't exist

CSCvb81003

WLC crashes as emWeb uses 100%

CSCvb81359

WLC 8540 HA. RMI ping and access to standby fail when using non-default ap-manager

CSCvb85576

Evaluation of wlc for CVE-2016-5195 (DIRTY CoW)

CSCvb89781

2700-B AP unable to join WLC: Unable to create temp dir "flash:/update"  LR= 0xc011e2dc

CSCvb90403

AP1810W hardware watchdog reset at PC= 0xc03b3ffc

CSCvb90793

AP name unknown in SNMP bsnDot11StationDeauthenticate traps

CSCvb92562

Evaluation of all for Openssl 1.0.1 September 2016

CSCvb94610

Restore command to disable GARP

CSCvb94697

2800/3800 11n macbook client has dropping connectivity while connecting to AP3800

CSCvb95147

AP 1572EAC unable to use 80MHz

CSCvc00358

WLC crash  "apfRogueTask_0" missed software watchdog

CSCvc09824

the AP2800 band select stats counter show zero

CSCvc13175

GLC-T SFP stopped working in CT5520 (1G Port down on 5520)

CSCvc15149

Barbados 8.2 MR4 - Not beaconing a SSID when it is in an AP group and SSID enabled later

CSCvc16755

AP3802 custom power level not initialized after reboot

CSCvc18699

Corsica: High pings drops  traffic connectivity drops seen 8.2.131.40

CSCvc23658

Clients not removed from flexconnect and capwap in APs flexconnect central-sw

CSCvc25669

rfidTask is causing a high CPU on the WLC

CSCvc29030

100MHz channel separation between 5G band with XOR in monitor mode

CSCvc31133

Unable to enable wlan with enabled selected option in GUI. Security: FT + Open

CSCvc31304

83MR1: AP syslog flood for TLV-DEC-ERR: cannot process TLV for TLV_DMS_CLIENT_REQUEST_PAYLOAD(325/0)

CSCvc32706

3800 APs: Not seeing all COS neighbors

CSCvc32856

Barbados: Sends a AQ Event as soon as RRM changes channel causing bad channel selection and changes

CSCvc33258

WLC: Unable to config RX-SOP threshold for IW3702 AP

CSCvc33511

SNMPv3 access failing with either unknown user / no response

CSCvc38214

2800/3800 Sending Acks to client at 54 data rate although Basic rate is 12 & 24

CSCvc39963

Barbados : FRA revert command failing to revert XOR to 2.4GHz

CSCvc40470

AP radio hang chatter: wl0: rxRingStuckDetect(271): RX-HANG Detected!!

CSCvc40564

TPC - Maximum/Minimum power level are not set as expected

CSCvc42566

1702I AP - radio resets observed due to CleanAir error count exceeded

CSCvc42741

AP3800/AP2800 : Failed to receive data keepalive and  Process capwapd gone

CSCvc42939

3800 AP duplicating multicast packets

CSCvc43232

2800/3800 uses 11n data rates to send data packets to 11b only clients failing to assoc

CSCvc43328

2800/3800 Sending Acks to client at 54 data rate although Basic rate is 12 & 24 in 8.2Mr4Esc

CSCvc45038

2800/3800 Beacon drift 25ms with offchannel/cleanair scanning @3sec mc9060 client drops

CSCvc48232

AP crash due to kernel panic at mhsm_transition

CSCvc50228

2800/3800 Sending Data packets to the 11g clients sometimes with messed up data rates

CSCvc50377

WLC7500: emWeb crash while doing "show run-config" on 8.0.110.11

CSCvc53578

2800/3800 11b only clients does not associate if HT is disabled

CSCvc53675

1852 AP - kernel backtrace at ol_ath_tx_mgmt_wmi_send+0x0/0x1e4

CSCvc74695

XOR radio pushes local-mode AP config for flex-mode AP causing Client disconnect

53 Replies 53

SYS light was flashing, console unresponsive, power cycle appears to have resolved it. APs downloading now.

Not exactly the same as you, but similar enough to mention.

I had an issue with 8.1.131 (I think that version) where pre-downloading software to the APs left the controller unresponsive. We have around 2000 APs. I couldn't SSH into it and the console didn't even respond. SNMP still worked as did syslog. Regular Wi-Fi traffic was unaffected. Everything returned to normal once pre-download finished.

We noticed the issue because Prime reported that both of the WLC power supplies had failed, which was obviously bogus.

Weirdness.

MUQ_1899_
Level 1
Level 1

Are there any reasons 8.2.151 not to be the suggested image for WLC 5520 but to be for the others?

Hi

No reason, it was a minor error on the suggestion rule, I just updated it , thanks for reporting 

regards

patrick.kofler
Level 1
Level 1

Hello Javier,

yesterday a security advisory was released regarding WME DoS vulnerability (CSCva86353)

There is however no explicit statement, if 8.2.151.0 is vulnerable or not. We are currently planning to roll out this image to our WLCs and would need a confirmation, if this vulnerability affects this release or not.

Best Regards,
Patrick

Hi Patrick

it is explicitly mentioned on the advisory and on the bug release notes, that version 8.2.130.0 and higher are fixed, thus 140,  150.0, etc. and anything after are not affected

regards

MUQ_1899_
Level 1
Level 1

Hello, do the 8.2.151.0 code was the last from this train? Are there going to be more releses from 8.2 or we should focus on 8.3/4 ?

My concern is 1/2/3800 APs.

Hello

we plan to do an additional 82MR6 for July timeframe, the interim code is already available here:

https://supportforums.cisco.com/discussion/13284941/82mr6-interim-release-availability

you can request access

This is the last planned release for 8.2 train, from that point, we will focus on 8.3 moving forward as next MD long life rlease

Regards

ivanchakarov
Level 1
Level 1

8.2.160.0(ED) is out for some days. :)

Review Cisco Networking for a $25 gift card