Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello! Having an issue since we upgraded our wireless controller to 8.10.121.0 where any laptops with the Intel 8265 or 7265 cards intermittently disconnect and reconnect. Very poor performance and cannot keep a consistent connection. I know on a pr...
We've one instalation with a Mobility Express (AIR-AP1852I-E-K9C) working with two AIR-AP1852I-E-K9 (Software 8-3-133-0 in the three cases). Recently we bought a new CAPWAP (AIR-AP1852I-E-K9) and we put the software 8-3-133-0 but can't connect with ...
Hi, I'm trying to joing a AIR-CAP2602I-E-K9 to my 1852i with mobility express. Regarding to https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8_4/b_cisco_mobility_express_8_4/b_Mobility_Express_Deployment_guide_chapter_0100.html th...
Hi team, What is the trick to enable AC and AX speeds on the 9130AXI-EWC? The CLI for 'ap dot11 5 dot11ac' indicates that A needs to be disabled first. Help says 'ap dot11 5 shutdown' will disable A, but as expected, shuts the whole radio off. Thank...
hi GuysI have a problem.I got a new MR33 and 4 new MR42e APs and should set them up.The APs are connected to a Cisco 2960 switch, switch port is configured as a trunk with Native VLAN 555.VLAN555 also assigns the IP address and comes on the Internet....
I have one of these and a couple of 1142 AP's that I would like to learn with.I've had this on a shelf for a long time now, and I pulled it off over the weekend and started taking a look at it again.I found that it is EOL and I cannot find anything o...
A client today was able to connect to the WLC via ap as normal. The user was then able to unauthenticated the device and connect to a spoofed SSID. What blocked him to go any further was PEAP to Cisco ISE. Question is, is there a setting within the...
I already tried ressetting and downgrade ap help me
we have 5200 controller with Config backup of this device. we need to migrate this to new 9800-L wireless controller. we have tried to convert backup from 9800 controller itself, it is showing translated config, unmapped and unsupported. require assi...
Hi Everyone,I have an AIR-CAP3502E-A-K9 with the autonomous (AP3G1-K9W7-M), Version 15.3(3)JF12, RELEASE SOFTWARE (fc1)All the CLI works as expected but the Web GUI give me a "404 not found error" anytime I press the Apply button to push a new config...
Hello everyone,I tried resetting my Cisco Aironet 1815i Mobility Express to Factory Default via CLI with the following commandsreset system Recover-ConfigAfter boot-up the access point still shows me the same SSID as before instead of the CiscoProvis...
Hi AllI know that with 802.11a/b/g you see wireless data rates advertised in the beacons etc, these normally go up to 54Mbit Are these data rates negotiated by the ap and client depending on the rssi ? Also, what about 802.11n and 802.11ac etc, what ...
Hi all,I'm new to the Meraki hardware and so far i'm really pleased with how it works and how fast you can configure the devices. But I have a problem with configuring 2 MS250 switches that i want to enable for Layer 3.I will explain everything i did...
I have two AP 1802 connect to the 3504 controller.In FlexConnect mode, one client connect to AP1 and the other connect to AP2 , with the same SSID and VLAN.Both client can get on the internet, but they cannot ping each other. If clients are on the sa...
