cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
4815
Views
0
Helpful
8
Replies

AP1850 unable to convert to mobility-express mode

Marwan Ruslan
Beginner
Beginner

I have 3  a new Access Points AIR-AP1852E-E-K9,

 

I am trying to transfer to mobility-express mode but it is show me the following error:

 

AP0CD0.F80C.1E70#ap-type mobility-express tftp://192.168.100.100/AIR-AP1850-K9-8-8-111-0.tar
Starting the ME image download...
It may take a few minutes to finish download.
If it is longer, please abort command, check network connection and try again

 

curl: (28) TFTP response timeout
transfer command failed
Image transfer failed. Please try again
AP0CD0.F80C.1E70#

 

Notes:

1) move files by tftp Server working well (tested with Cisco Switch 2960)

2) Wired0 Interface UP and ping able with tftp server

3) firewall disabled in tftp Server

4) after initialize command taken around 3 Minutes then give me that error

5) AP continuously rebooting (connected by POE to Cisco Switch 2960)

2 Accepted Solutions

Accepted Solutions

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

@Marwan Ruslan wrote:

ap-type mobility-express tftp://192.168.100.100/AIR-AP1850-K9-8-8-111-0.tar

1) move files by tftp Server working well (tested with Cisco Switch 2960)


In the Cisco switch, is the command "tftp flash:AIR-AP1850-K9-8-8-111-0.tar" present? 

NOTE:  Don't use 8.8.111.0.  Use 8.5.135.0.  

View solution in original post

Sandeep Choudhary
VIP Mentor VIP Mentor
VIP Mentor

As Leo mentioned...

Either use 8.3.143.0 or 8.5.140.0 version software to upgrade.

 

Regards

Dont forget to arte helpful posts

View solution in original post

8 Replies 8

marce1000
VIP Mentor VIP Mentor
VIP Mentor

 

- Enable logging on the tftpd server and check if there are any connections coming from the AP or not.

M:

there is no any connections coming from AP

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

@Marwan Ruslan wrote:

ap-type mobility-express tftp://192.168.100.100/AIR-AP1850-K9-8-8-111-0.tar

1) move files by tftp Server working well (tested with Cisco Switch 2960)


In the Cisco switch, is the command "tftp flash:AIR-AP1850-K9-8-8-111-0.tar" present? 

NOTE:  Don't use 8.8.111.0.  Use 8.5.135.0.  

@Leo Laohoo
In the Cisco switch, is the command "tftp flash:AIR-AP1850-K9-8-8-111-0.tar" present?

no i tested cisco switch with same tftp Server and .bin file

The error message states "TFTP response timeout". This means the AP is able to contact the TFTP server but the TFTP server is not handing out the file. This could mean the command "tftp flash:AIR-AP1850-K9-8-8-111-0.tar" may not be present.

I restart TFTP Serevr and used 8.5.135.0 Version then working fine, Thank you

Sandeep Choudhary
VIP Mentor VIP Mentor
VIP Mentor

As Leo mentioned...

Either use 8.3.143.0 or 8.5.140.0 version software to upgrade.

 

Regards

Dont forget to arte helpful posts

Matias Acuna
Beginner
Beginner

in my case, i changed the pc where tftp server was located, and it's worked fine

Regards

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: